Hi, I need to install freebsd on windows machine. The bootloader must be in a usb key, preferably in the second partition.
Something like this:
ada0s3a as root partition;
ada0s3b as swap partition;
da1s2 (usb key) as boot partition.
I have tried several ways to do this without success.
I installed FreeBSD 11.3. I tried to connect my Garmin gpsmap device via USB, however device not get detected/enumerated. When going through dmesg following error shows. I am new to FreeBSD. Any suggestions would be appreciated :)
Thanks in advance.
usb_alloc_device: set address 2...
If you are looking to buy a really compatible and trustworthy wifi usb adapter for freebsd
Search ebay with these keywords copy the entire text: RTL8812AU 1200M 5G Wireless Network Card USB 3 Wi-Fi-Receiver
and paste it on ebay search.
I'm using it right now and it is crazy compatible with...
Good day to every one
i read a Little Bit on the site
then downloaded dvd1 witch is about 3gb 1/2 on a usb
then asked me for user and password so user root pass nothing
still unable to log in
i would Like to try it out first before i do a full install
A month go I noticed missed characters when I type text/commands etc.
I decided to replace my cheap USB keyboard with something better.
I purchased a $50 "mechanical" keyboard, but nothing has changed – I still see missed characters. It looks like an anti-bouncing filter cuts certain keystrokes...
My laptop is a Lenovo V110-15AST AMD A9-9410
I downloaded the img file to write onto a USB 3 8GB stick.
After, I then used dd to write the image
sudo dd if=/home/ukbeast/Downloads/FreeBSD-12.0-RELEASE-amd64-memstick.img of=/dev/sdb bs=1M conv=sync
I then have 3 partitions on the stick as:
Scenario: I have a 1 BeagleBone black and a laptop, the laptop runs FreeBSD-11.1
1] If I run the BBB with Linux Debian, when I plug the BBB usb to the laptop, in the laptop I see a nice ue interface that I can easily configure as a network adapter and comunicate with the BBB over usb. It works...
Hi, i am trying to burn Ubuntu or WIndows10 iso file to the Usb and i think Kde-Services will be useful for this. (use dd command)
Dolphin: Control -> Configure Dolphin... -> Services -> Download New Services... -> Installed kde-services plug-in but it doesnt work. How can i make it work?
I installed FreeBSD 11.1 with Kde and it works. (It doesnt have gpu accelerator but works anyway)
Question is how can I create bootable Windows10 usb or Ubuntu usb in FreeBSD?
I downloaded the ubuntu-16.04.4-desktop-amd64.iso file. If it's possible I can download Windows10-x64.iso too.
Hi again! This time I want to know how to create a wireless network (WiFi).
I have 11.1-RELEASE-p6 on a i386 processor.
And yes, also I have a wifi USB adapter. It is a TP-LINK TL-WN722N.
I want to know, what I need to configure to be able to use this USB as an antenna?
I know this question has probably been asked a thousand times here (sorry) but I'm in need of a quality wireless USB dongle with very good range (i.e. antenna).
Currently I'm using an Edimax nano dongle that I bought off Amazon which connects fine, but the signal is very weak. I'm sure with a...
Hi, I have problems there.
System: FreeBSD 12
Hardware: Raspberry PI 3
+ 4x USB Ethernet AX88179
I have the problem that with each reboot all UE USB network adapters are remixing and therefore are no longer useful. I can not always change the config for the entire network and rearrange all 5...
Has anyone succeeded in getting original Playstation 2 Dualshock 2 controllers to work with FreeBSD?
I have two PS2 Dualshock analogue controllers, and a cheap USB adapter from ebay. It all works fine on PS2 / Windows (with adapter), so I know it is not a hardware issue.
My issue is this:
First up, i'm super new to FreeBSD, so please go easy on me.
(i'm rather familiar with Linux though)
I have a STM32 microcontroller based USB device that presents itself as a CDC VCP device.
I'm using ST's USB CDC device library.
On attaching the device i see in the kernel log...
Sorry if I double the thread, but I didn't find answer.
If I write a usb stick img in the Windows (tried XP and 7) then after direct write finished I have BSOD and rebooting. The same if I just insert FreeBSD installation usb to the Windows machine. So if Windows try to mount FreeBSD...
I am having problem with USB Ethernet adapter (AX88179) running FreeBSD 11.1, all the ethernet functions work, but it has much lower throughput compare the same PC running Debian 9. I tested it by running iperf3 between two PCs, the results show high Retr count.
The AX88179 is listed under...
I'm having a problem with a HiFace Two DAC connected to an Ubuntu guest on VirtualBox.
The host is a NAS4Free (FreeBSD based).
On a bare Ubuntu I get this module correct working and reported like this in Ubuntu:
[1191641.895471] usbcore: registered new interface driver snd-usb-hiface...
I am running FreeBSD 11 on a raspberrypi-B. The built-in ethernet adapter is working fine with no extra configuration. I have bought an external USB ethernet adapter and trying to get it to work.
The external adapter is recognized by the kernel: in /var/run/dmesg.boot there are the following...
I'm new in using FreeBSD 11 but really I want to make it my primary system with arch.
I read a lot in FreeBSD forum and handbook, I'm glade to do that.
I begin with installed it in VirtualBox and take a time until i realize I'm ready to do it in my hard like a primary partition with other...
Anyone have experience with this product or similar high sample rate DACs on FreeBSD 11? I'm setting up a dedicated Windows box soon and/or emulation with Xen or bhyve, so I'm still going to get it regardless and will have a chance to test it myself.
Supposedly it requires proprietary drivers...