ethernet

  1. NapoleonWils0n

    Solved rc.d netif restart lagg0 and pf

    im using a lagg failover device with a usb ethernet adaptor the issue is the lagg0 device doesnt pick up the ethernet device in ifconfig ( post at the bottom explains the problem in detail ) it should have this line under lagg0 in ifconfig laggport: ue0 flags=5<MASTER,ACTIVE> but it doesnt...
  2. NapoleonWils0n

    lagg failover with a external wifi card

    you can create a lagg failover device to easily switch between wired and wireless using the built in wifi but its also possible to use an external usb wifi card as well in this example i will be using a Alfa-AWUS036NH wireless card...
  3. NapoleonWils0n

    Create a lagg failover interface to switch between ethernet and wifi

    Configure the wireless device as a secondary which is only used when the Ethernet connection is not available. With lagg(4), it is possible to configure a failover which prefers the Ethernet connection, while maintaining the ability to transfer data over the wireless connection. This is...
  4. R

    Realtek driver in 14.2?

    Will the 2.5 gb ethernet re driver be in the base for 14.2 or will we have to continue to use the one in ports? It comes standard on many motherboards now. Rick
  5. jcarnat

    Issue with USB Thunderbolt network adapter

    Hi, I have installed FreeBSD 14.1 on a ThinkPad X280. I have connected it to the HUB of my Dell U2723QE Monitor via USB/Thunderbolt ; this provides HDMI output, USB 3 Hub (where a mouse and a keyboard are connected) and Ethernet adapter. Everything works Ok except the Ethernet connection. When...
  6. christhegeek

    Any help with the integrated Intel 82579LM Ethernet Adapter ?

    Any help with the integrated Intel 82579LM Ethernet Adapter ? It doesn't seem to work , i have ordered a new pci ethernet card anyway and its possible to arrive until the end of the week , this ethernet chipset is awful !
  7. I

    Networking card (10g ethernet and wi-fi 6e) compatibility

    I'm trying to find out if these 2 networking cards are compatible with FreeBSD. Specifically, I need bhyve to "passthru" them into a guest VM (either FreeBSD or OpenBSD). 10G Ethernet card Wi-fi 6E card I went through the hardware list and found something "TP-Link" but it does not state the...
  8. U

    Support for Marvell® AQC113CS-B1-C 10Gbps LAN

    I have the MSI Meg X670E Ace. Neither the wifi(Not supported on Linux either) or Ethernet work. The controller it uses is AQC113, which is supported on Linux. However appears to be closed source. Are there any plans of development on getting it to work natively?
  9. K

    Switching between network adapters

    Hi Everyone, My laptop has both Ethernet and wireless cards, managed by the em(4) and iwn(4) drivers, the latter being associated with wlan0. Normally Ethernet is not connected, and I'm using wifi only. Sometimes I need to transfer a large file on my subnetwork, and for this I'd like to plug...
  10. Sergei_Shablovsky

    Solved Original Intel EXPI9404PTG2L20 EXPI9404PT PRO/1000 PT vs Fujitsu PRO/1000 PT Quad Port Gigabit Network Card PCI-E D2745-A11 low profile

    What is real difference in network performance (in real life complicated environment, i.e. a lot of packets different sizes, etc...) between this one Original Intel EXPI9404PTG2L20 EXPI9404PT PRO/1000 PT Quad Port Server Adapter Intel 82571GB Launch Date Q1'07 PCIe 1.0a Specification...
  11. F

    Can I compile Linux hardware code with FreeBSD?

    So I have a close-source wi-fi card. It works fine with windows ofc and fine with Linux because Ubuntu's developers develop a hardware support for that driver and its open-source. So Im really enjoying using FreeBSD but not being able to connection internet without ethernet cable or extra wi-fi...
  12. D

    NUC10i7FNH2 with I219V ethernet controller on 12.1-RELEASE not detected?

    Hi! I have purchased one of that brand new NUC10i7FNH2, but it doesn't detect any network interface than loopback. :( Anything I can do to make it work? Thank you!
  13. A

    Realtek usb to ethernet card not working

    I get on bootup: ure0 on uhub 2 ure0: <Realtek USB 10/100/1000 LAN, class 0/0. rev 3.00/30.00. addr 8> on usbus0 miibus1: <MII bus> on ure0 rgephy1: <RTL8251/8153 1000BASE-T media interface> PHY0 on miibus1 rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 1000baseTX-FDX, 1000baseT-FDX...
  14. Nicola Mingotti

    Solved About USB-Ethernet in BeagleBone Black

    Scenario: I have a 1 BeagleBone black and a laptop, the laptop runs FreeBSD-11.1 1] If I run the BBB with Linux Debian, when I plug the BBB usb to the laptop, in the laptop I see a nice ue interface that I can easily configure as a network adapter and comunicate with the BBB over usb. It works...
  15. W

    issues - Raspberry PI 3 as a router with 4 additional USB network cards

    Hi, I have problems there. System: FreeBSD 12 Hardware: Raspberry PI 3 + 4x USB Ethernet AX88179 I have the problem that with each reboot all UE USB network adapters are remixing and therefore are no longer useful. I can not always change the config for the entire network and rearrange all 5...
  16. Shaz

    Solved 10mbit on ifconfig, but 1gbps capable + cat6 direct to router

    This has been driving me nuts since I got FreeNAS on this machine. I'd like to know why I'm stuck at 10mbit. Network transfers via SMB are at a flat line 9.8mbps (1.12mB/s). SFTP and FTP both 9.7mbps. Running ifconfig reveals the following: media: Ethernet autoselect (10baseT/UTP...
  17. G

    FreeBSD 11 / rpi-B: external USB ethernet adapter cannot be configured

    I am running FreeBSD 11 on a raspberrypi-B. The built-in ethernet adapter is working fine with no extra configuration. I have bought an external USB ethernet adapter and trying to get it to work. The external adapter is recognized by the kernel: in /var/run/dmesg.boot there are the following...
  18. jayxkanz666

    Can't connect to anything

    Hey there! So, I'm pretty new to to the FreeBSD forums (signed up today), and I seem to be having a strange issue with internet on FreeBSD. The internet worked fine for about 1 hour a couple of days ago, then suddenly stopped working. My Ethernet controller is a Qualcomm Atheros AR8162 Fast...
  19. aragats

    Solved RS-232 over Ethernet?

    Is there any simple way of forwarding a serial port over Ethernet? Thanks for ideas!
  20. korund

    Network interfaces aren't picking up media on boot

    Dear all, I've moved my lovely server to the datacenter and now pulling my hair out while trying to understand why both of /dev/igb interfaces aren't picking up Ethernet connection on boot. Tested with both 10.3-REL and 11.0-REL. When system is booted, running ifconfig | grep status over iKVM...
Back
Top