I just can't make a USB BT dongle work.
The output of "usbconfig -d ugen1.3 dump_device_desc" is following:
ugen1.3: <Realtek Bluetooth Radio> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (500mA)
bLength = 0x0012
bDescriptorType = 0x0001
bcdUSB = 0x0110
I am moving my existing Freebsd install to another system to upgrade CPU. However, the network interface on the new motherboard is not visible and therefore I can't connect to the internet. It is a Realtek network interface.
What is the best way to install the realtek network driver with no...
I have a Realtek RTL8192EU USB NIC and the transfer (download) speed is very slow (maximum of 200k/s). On Linux I get a medium speed of 1000k/s, which is what I would expect and also matches up with the output of speedtest-cli.
in /etc/rc.conf I have:
I have a Intel Atom D2700 based nettop and FreeBSD 12.2 i386 fresh install.
That PC has a integrated Wi-Fi on a USB bus based on a RTL8191S chipset:
# usbconfig list
ugen2.1: <Intel UHCI root HUB> at usbus2, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen3.1: <Intel UHCI root...
I've an old Hp Microserver N36L with XigmaNAS 18.104.22.168 (FreeBSD 12.1-RELEASE P9). The on board NIC is broken, so until now I used a Intel PCie etc card. All worked fine.
I wanted to fresh up a little bit the NAS, so I bought a USB3+gigabit etc card (branded Delock), It has the Realtek...
I installed FreeBSD 12.1 on my desktop, which has a TP-Link TL-WN881ND, which in itself has the Realtek RTL8192EE.
I went through the handbook and found that (unless I am missing something), I should use the XP drivers via ndisgen as I did not find a driver anywhere in the docs or...
Anyone knows if this is supported?
Running a Lenovo T470 with Intel atm, but seems to be a bit slow.
Noticed that they have whitelisted the Realtek card below, not sure if it would work better or not at all with FreeBSD.
Realtek RTL8822BE - Wi-Fi 2x2 802.11ac + BT4.1, M.2 card
Could it work...
I have an Asus E203N which doesn't support the Trackpad, 802.11ac, and audio in FreeBSD 12.0 p10. I was able to compile ig4, acpi_iichid, iichid support into the kernel with a patch to get the Trackpad working (would like to get evdev support working). I have an external rtwn device...
I have two Realtek RTL8111G card on my mainboard, one is defined as WAN and other is LAN, using the box as router (pfsense).
After around 1hour the routing freeze if I disable he WAN and than enable again it start working.
Currenly I`m running on the Binary 1.95
Is there other also...
FreeBSD newbie here. I just installed FreeBSD 12.0-RELEASE AMD64 on a small box and am having issues getting the PCI realtek wireless network card to work.
Running ifconifg -a displays the motherboards ethernet controller and the loopback device, but not my wireless card. However, running...
I have a lenovo all in one pc that has the Real Tek 8821AE wireless card. I have gone on the manufacturers website and downloaded the .sys and .inf files for ndisgen, and when I run the program to create the module i get all the way to the point where it says:
Generating Makefile... done...
This has been driving me nuts since I got FreeNAS on this machine. I'd like to know why I'm stuck at 10mbit. Network transfers via SMB are at a flat line 9.8mbps (1.12mB/s). SFTP and FTP both 9.7mbps.
Running ifconfig reveals the following:
media: Ethernet autoselect (10baseT/UTP...
I am running FreeBSD 11 RC1 on a raspberry pi 2. I have a urtwn usb wifi device. I can get it associated with my access point, but it just won't seem to send/receive any traffic: not DHCP packets, and not pings if I configure it statically.
# uname -a
FreeBSD rpi2 11.0-RC1 FreeBSD...
I try desperately to record audio from my computer, but it seems impossible.
here is output from mixer:
Mixer vol is currently set to 50:50
Mixer pcm is currently set to 90:90
Mixer speaker is currently set to 50:50
Mixer line is currently set to 50:50
Mixer mic is currently set to...
Just setting on /boot/device.hints below
Speaker works with very good sound quality. headphone have no sound but sounds still came out of speaker. I tried several configurations but no one worked.