code7395 said:dear moderator , i promise i will get a chat alternative after this. sorry.
egorenar till i get an icq touch, please review ur code, now it doesen't wait for if config to show the panic message above and reboot the system, it does it as soon as i plug the device in.
sorry mod.
greyulv said:Hey egorenar
Looking forward for the 7.2 support for 802.11n and rt2860. Got a new N++ router last week.
G
yandzee said:Or connect but ping google.com doesn't work.
yandzee said:I can't configure connection with y router. Help please.
Not connect.Code:ifconfig rt28600 ssid my_router wepmode on wepkey my_key authmode shared ifconfig inet 192.168.1.100 net mask 255.255.255.0
I use WEP Shared connection!
ifconfig wlan0 create wlandev rt28600 wlanmode sta
ifconfig wlan0 ssid my_router wepmode on wepkey my_key authmode shared
ifconfig wlan0 inet 192.168.1.100 net mask 255.255.255.0
egorenar said:Does anybody have any idea where i can find net80211 mailing list or IRC. I have some questions regarding 802.11n stack implementation in FreeBSD and i don't know whom to ask.
:e :e :e
yandzee said:ifconfig wlan0 create wlandev rt28600 wlanmode sta
ifconfig:SIOCIFCREATE2: Invalid argument
FreeBSD 7.2 RELEASEegorenar said:Are you using FBSD 7 or FBSD 8 ?
egorenar said:Of course, you can't have 2 default gateways Either you must disable the Ethernet NIC or you need to modify the routing table manually.
But you said in one of your previous posts that your system crashed. Did you figure out what was wrong ?
:e :e :e
yandzee said:FreeBSD 7.2 RELEASE
egorenar said:OK, then forget about "ifconfig create", it's only for FBSD 8.
You have problems with routing ?
What says "netstat -nr" ?
:e
ale0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=319b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_MCAST,WOL_MAGIC>
ether 00:23:54:63:50:a6
media: Ethernet autoselect (none)
status: no carrier
rt28600: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 00:22:43:4a:47:2d
media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
status: no carrier
ssid "" channel 1 (2412 Mhz 11b)
authmode OPEN privacy OFF txpower 50 bmiss 7 scanvalid 60 wme burst
bintval 0
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif Expire
127.0.0.1 127.0.0.1 UH 0 0 lo0
Internet6:
Destination Gateway Flags Netif Expire
::1 ::1 UHL lo0
fe80::%lo0/64 fe80::1%lo0 U lo0
fe80::1%lo0 link#3 UHL lo0
ff01:3::/32 fe80::1%lo0 UC lo0
ff02::%lo0/32 fe80::1%lo0 UC lo0
yandzee said:ifconfig
Code:ale0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=319b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_MCAST,WOL_MAGIC> ether 00:23:54:63:50:a6 media: Ethernet autoselect (none) status: no carrier rt28600: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 00:22:43:4a:47:2d media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier ssid "" channel 1 (2412 Mhz 11b) authmode OPEN privacy OFF txpower 50 bmiss 7 scanvalid 60 wme burst bintval 0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000
netstat -nr
Code:Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire 127.0.0.1 127.0.0.1 UH 0 0 lo0 Internet6: Destination Gateway Flags Netif Expire ::1 ::1 UHL lo0 fe80::%lo0/64 fe80::1%lo0 U lo0 fe80::1%lo0 link#3 UHL lo0 ff01:3::/32 fe80::1%lo0 UC lo0 ff02::%lo0/32 fe80::1%lo0 UC lo0
I can set up rt28600.egorenar said:status: no carrier
Your rt28600 device is not associtaed with an AP.
Are you using wpa_supplicant to associate ?
yandzee said:What is AP mode?
how to set up wpa_supplicant?
need authmode shared
egorenar said:Write to my ICQ or Jabber account, then i could help you faster.
yandzee said:What is you icq number?