Hello,
I'm getting no response from this mceusb (MCE) remote and IR receiver (receiver Model No: OVU400309/00).
FreeBSD Version:
Relevant software versions:
Commands with output:
I'm not really sure where to go from here. Am I doing anything wrong? I am happy to do further testing. Let me know if you need further info.
Cheers!
I'm getting no response from this mceusb (MCE) remote and IR receiver (receiver Model No: OVU400309/00).
FreeBSD Version:
8.3-RELEASE-p3 FreeBSD 8.3-RELEASE-p3 #0: Tue Jun 12 00:39:29 UTC 2012 root@amd64-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC amd64
Relevant software versions:
multimedia/webcamd - webcamd-3.6.0.1_1
comms/lirc - lirc-0.9.0_3,1
multimedia/cuse4bsd-kmod - cuse4bsd-kmod-0.1.24
comms/lirc - lirc-0.9.0_3,1
multimedia/cuse4bsd-kmod - cuse4bsd-kmod-0.1.24
Commands with output:
# usbconfig -d 6.2 dump_device_desc
Code:
ugen6.2: <eHome Infrared Transceiver Philips> at usbus6, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
bLength = 0x0012
bDescriptorType = 0x0001
bcdUSB = 0x0110
bDeviceClass = 0x0000
bDeviceSubClass = 0x0000
bDeviceProtocol = 0x0000
bMaxPacketSize0 = 0x0010
idVendor = 0x0471
idProduct = 0x0815
bcdDevice = 0x0000
iManufacturer = 0x0001 <Philips>
iProduct = 0x0002 <eHome Infrared Transceiver>
iSerialNumber = 0x0003 <PH00beri>
bNumConfigurations = 0x0001
# webcamd -d 6.2
Code:
[url=http://pastebin.com/fSBLh10n]Output from webcamd (with debug)[/url]
# mode2 -d /dev/lirc0
Code:
<no output>
# usbdump -i usbus6 -vvv
Code:
[I](after running webcamd then mode2)
<snip - full output over 6mb>[/I]
20:15:56.195266 usbus6.2 SUBM-BULK-EP=00000081,SPD=FULL,NFR=1,SLEN=0,IVAL=0
frame[0] READ 16 bytes
flags 0x16 <SHORT_XFER_OK|SHORT_FRAMES_OK|PROXY_BUFFER|0>
status 0xcf823 <OPEN|TRANSFERRING|STARTED|SHORT_FRAMES_OK|SHORT_XFER_OK|BDMA_ENABLE|BDMA_NO_POST_SYNC|BDMA_SETUP|CAN_CANCEL_IMMED|DOING_CALLBACK|0>
20:15:56.197112 usbus6.2 DONE-BULK-EP=00000081,SPD=FULL,NFR=1,SLEN=0,IVAL=0,ERR=STALLED
frame[0] READ 0 bytes
flags 0x16 <SHORT_XFER_OK|SHORT_FRAMES_OK|PROXY_BUFFER|0>
status 0xef821 <OPEN|STARTED|SHORT_FRAMES_OK|SHORT_XFER_OK|BDMA_ENABLE|BDMA_NO_POST_SYNC|BDMA_SETUP|CURR_DMA_SET|CAN_CANCEL_IMMED|DOING_CALLBACK|0>
I'm not really sure where to go from here. Am I doing anything wrong? I am happy to do further testing. Let me know if you need further info.
Cheers!