If the cupsd service is running but still doesn't connect, have you a firewall enabled?the web interface page http://127.0.0.1:631 times out!
If the cupsd service is running but still doesn't connect, have you a firewall enabled?the web interface page http://127.0.0.1:631 times out!
HiThe distinction of the error is important, is it a "connection timed-out", or a "connection refused"? Timed out means it sent a SYN packet but nothing responded. This is usually a firewall issue (firewalls tend to 'drop' packets). A connection refused means it received a RST after a SYN. This typically happens if you try to connect to a 'closed' port, i.e. the service isn't running or bound to the wrong IP address.
Any of the other firewalls enabled perhaps? How did you disable IPFilter? Please post your rc.conf.Already disabled ipfilter.
This is often an indication of a firewall.Checked with nmap, port 631 is in state FILTERED.
Contents of rc.conf:Any of the other firewalls enabled perhaps? How did you disable IPFilter? Please post your rc.conf.
This is often an indication of a firewall.
clear_tmp_enable="YES"
syslogd_flags="-ss"
sendmail_enable="NONE"
hostname="localhost.localdomain"
local_unbound_enable="YES"
sshd_enable="YES"
moused_enable="YES"
ntpd_enable="YES"
powerd_enable="YES"
# Set dumpdev to "AUTO" to enable crash dumps, "NO" to disable
dumpdev="AUTO"
wlans_iwm0="wlan0"
ifconfig_wlan0="WPA SYNCDHCP"
create_args_wlan0="country IN regdomain FCC4"
pf_enable="YES"
pf_rules="/etc/pf.conf"
pf_flags=""
pflog_enable="YES"
pflog_logfile="/var/log/pflog"
pflog_flags=""
dbus_enable="YES"
hald_enable="YES"
kld_list="i915kms"
kld_list="/boot/modules/i915kms.ko"
#gdm_enable="YES"
#gnome_enable="YES"
clamav_freshclam_enable="YES"
clamav_clamd_enable="YES"
ossechids_enable="YES"
tor_enable="YES"
polipo_enable="YES"
#slim_enable="YES"
tor_setuid="YES"
#ipfilter_enable="YES" # Start ipf firewall
#ipfilter_rules="/etc/ipf.rules" # loads rules definition text file
#ipv6_ipfilter_rules="/etc/ipf6.rules" # loads rules definition text file for IPv6
#ipmon_enable="YES" # Start IP monitor log
#ipmon_flags="-Ds" # D = start as daemon
# s = log to syslog
# v = log tcp window, ack, seq
# n = map IP & port to names
#gateway_enable="YES" # Enable as LAN gateway
#ipnat_enable="YES" # Start ipnat function
#ipnat_rules="/etc/ipnat.rules" # rules definition file for ipnat
static_arp_pairs="gw"
static_arp_gw="192.168.1.1 00:01:02:03:04:05"
#blacklistd_enable="yes"
#sddm_enable="YES"
cupsd_enable="YES"
devfs_system_ruleset="system"
Already disabled ipfilter.
pf_enable="YES"
pf_rules="/etc/pf.conf"
pf_flags=""
kld_list="i915kms"
kld_list="/boot/modules/i915kms.ko"
hald_enable="YES"
It's not a good idea to have two firewalls running at the same time.
By the way, you can do a bit of cleaning in your rc.conf:
kld_list="i915kms" kld_list="/boot/modules/i915kms.ko"
... these two lines do the same, you can remove the second one.
hald_enable="YES"
... hald doesn't exist anymore, you can remove this.
[HEADING=1]Add Printer EPSON_L6460_Series Error[/HEADING]
Unable to get list of printer drivers:
[QUOTE]
No error: 0
[/QUOTE]
NOW that CUPS is up and running, it is a good time to go back up this thread, and look at OpenPrinting link I gave you earlier. Hopefully your printer is there, and has a CUPS driverHi
Disabled pf & stopped it. Now I am able to login. When adding my printer get following error:
Code:[HEADING=1]Add Printer EPSON_L6460_Series Error[/HEADING] Unable to get list of printer drivers: [QUOTE] No error: 0 [/QUOTE]
Already have gutenprint installed.
Thanks
rraj
Well, at least there is a port of the manufacturer's Linux "driver", using the linuxulator ... and this should come with PPDs, so you can just add the printer in CUPS. I thought OP had already installed this port. If so, I unfortunately have no idea what "Unable to get list of printer drivers" should meanNOW that CUPS is up and running, it is a good time to go back up this thread, and look at OpenPrinting link I gave you earlier. Hopefully your printer is there, and has a CUPS driver
HiNOW that CUPS is up and running, it is a good time to go back up this thread, and look at OpenPrinting link I gave you earlier. Hopefully your printer is there, and has a CUPS driver
You might want to look at your printer's manufacturer-provided documentation to figure that one out. One place that might help is is Wikipedia explanation of the Bonjour service: https://en.wikipedia.org/wiki/Bonjour_(software) . Most likely, your printer does support Bonjour, but manufacturer docs might refer to it by a different name - ZeroConf, mDNSResponder, and the like - the wikipedia article provides more clues. Another term to pay attention to is Avahi - it's another implementation of the same protocol, available as net/avahi in ports. Same capabilities, different name. So, check to see that you have Avahi installed.Hi
Used linuxulator to install printer drivers provided by manufacturer (rpm files).
Still the same error as before.
lpinfo --include-schemes dnssd -v
, does not yield anything i.e. back to prompt.
Does that mean 'Bonjour' is not supported by my Printer?
Thanks
rraj
Hi
I would really not recommend that. That's why I suggested you use the port of the original (Linux) driver instead, see earlier in the thread. This will make sure the filter is installed where CUPS on FreeBSD expects it and all dependencies (linux-c7-* ports) are installed as well.Used linuxulator to install printer drivers provided by manufacturer (rpm files).
HiI would really not recommend that. That's why I suggested you use the port of the original (Linux) driver instead, see earlier in the thread. This will make sure the filter is installed where CUPS on FreeBSD expects it and all dependencies (linux-c7-* ports) are installed as well.
Just installing some rpm will most likely make it worse though.Having epson FreeBSD port installed did not help either!
ummm... if you look forUPnP is already installed!
upnp
on ports.freebsd.org, you'll get many hits, including devel/upnp... which ones exactly do you have installed? Please post the output of pkg info | grep upnp
... The UPnP SDK is definitely not what you need. Stuff like net/gssdp or net/gupnp are a better bet to satisfy the dependencies... Avahi should be installed, it's a CUPS dependency... Also, the ports do have separate packages for Epson printers, just look for epson
on ports.freebsd.org...HiAh, you might want to use the word localhost, instead of the IPv4 address... have you tried that?
Oh, and one more thing: Is the CUPS server even running?
Code:# service cupsd status # service cupsd restart
Hiummm... if you look forupnp
on ports.freebsd.org, you'll get many hits, including devel/upnp... which ones exactly do you have installed? Please post the output ofpkg info | grep upnp
... The UPnP SDK is definitely not what you need. Stuff like net/gssdp or net/gupnp are a better bet to satisfy the dependencies... Avahi should be installed, it's a CUPS dependency... Also, the ports do have separate packages for Epson printers, just look forepson
on ports.freebsd.org...
root@localhost:~/Desktop # pkg info | grep upnp