So I've been playing with a FreeBSD virtual setup to test network functionality, and the routing is awesome, especially vlan subinterfaces.
Now I'm trying to make the FreeBSD machine behave as a network switch. One way to do that is to create a bridge and add all the ports to the bridge. This...
Normally, we have to put the network interface (e.g. em0 or igb0) when setting up jails. For example:
If the network interface (physical card) is being sent as pass-thru via bhyve to a virtualized operating system running within...
Hey! So this is my second thread on the FreeBSD forums, and I'm trying to get the USB-AC51 by ASUS to work in FreeBSD. In the FreeBSD 10.1-RELEASE release notes, it says that "urtwn(4) has been updated to support the ASUS USB-AC51", so it's supposed to be working.
I've tried putting...
Greetings! I am having trouble understanding how to configure my network in the manner I desire. I googled around and searched the forums and have come across all kinds of stuff however I'm not sure what is best practice and such. I saw a lot of terms such as aliases, dummy interfaces, taps...
Hi there :)
Someone has demonstrated for a while running OpenStack hosted on FreeBSD 11. Described right here
For me that sounds awesome. I would like to have a similar setup now with FreeBSD 11 XEN and hosting OpenStack on Dom0. The minimum goal is to run FreeBSD as an Nova Compute
I created a bad alias when attempting to setup networking for a jail.
ifconfig bce0 alias 192.168.1.111 netmask 0xffffff00 broadcast 192.168.4.255
when I should have done this
ifconfig bce0 alias 192.168.4.111 netmask 0xffffff00 broadcast 192.168.4.255
I've corrected the problem but...
I have a Windows 10 Workstation where I run a FreeBSD 10.3 Guest server over VMWare 12. This FreeBSD VM is meant to run multiple Apache/PHP/Wordpress instances on multiple jails.
The FreeBSD guest is bridged through the HOST Ethernet NIC, where the HOST has the IP...
I'm currently running 11.0-RELEASE-p7 in one of those cheap 1€ aruba VPS machines servers for fun.
Their current control panel doesn't support ipv6 auto configuration therefore it must be configured manually.
I'm able to configure the ipv6, but I lost connectivity a few seconds after boot.
Hi Network Guru's-
I've been running 11-Release branch since 11 was well.... released. I think I'm on 11-RELEASE-p2. I compiled my own kernel to enable vimage and use iocage for jails. I am not using pf or doing anything "exotic" with networking (this is behind a separate firewall).
I'm trying to set up internet connection on FreeBSD 11.0-RELEASE running at VMware VM but, when I try to ping google IPs, I get a 100% loss.
Here is my rc.conf.
I use default (for vmware) NAT connection and try to route traffic trought gateway ip (192.168.149.2). Please tell me...
I created bridge0 (172.16.0.1) device with few tapX network devices (172.16.0.2-X) (bridged together by bridge0) for bhyve vms.
Then I created NAT (pf.conf), that solves networking via wlan0 (wifi card). Why? Because simple bridging doesn't work with wlan0/wifi interfaces (NAT works)...
We're facing quite slow uploading speed on FreeBSD-10.X both over HTTP (NGINX) & over FTP. Hardware is quite strong with 4x1Gbps LACP / 65G RAM / 12x3TB SATA . There's not much load over HDDs so i suspect that maybe tcp tuning has some problem. Here is my sysctl.conf...
I'm currently running a server based on FreeBSD 10.3. I'm using jails to separate all the running services. Since I only have one public IPv4 address, I use PF and a nginx-proxy to redirect to the specific jails inside the NAT.
My plan is to use 11.0 and it's enhanced bhyve features to...
I'm trying to set up a server with FreeBSD 11.0-RELEASE on a VMware VM @ OVH (hosting company) but, when I try to ping, I get a "host name lookup failure".
It's very strange because I copied /etc/rc.conf and /etc/resolv.conf from the previous working installation with FreeBSD...
LACP stopped working on FreeBSD-10.2 release with following error :
Interface stopped DISTRIBUTING, possible flapping
More than that, we're unable to execute any command in FreeBSD console. Here is the screenshot where we're trying to...
I will try to explain my setup as clear as I can. I have a Windows 10 Workstation where I run a FreeBSD VM on VMWare 12.
This FreeBSD VM is meant to run multiple Apache/PHP/Wordpress instances on multiple jails.
The FreeBSD guest is bridged through the HOST Ethernet NIC, where...
I am trying to share a single 10Gb ethernet outlet in my office between two machines by bridging across a FreeBSD server using the second port on its 10Gb card. The bridge works quite well, and the other machine gets network service. The FreeBSD server, however, does not, even though I added an...
I am looking to setup two physical nics with two different ip addresses and two different gateways. The basics:
10.2-RELEASE FreeBSD 10.2-RELEASE #0 r286666: Wed Aug 12 19:31:38 UTC 2015
I am looking to make one nic...
We're trying to achieve 4Gbps throughput using 4x1Gbps LACP mode but only able to achieve 2Gbps other 2x1Gbps shows this status :
Here is our network config :
Worth mentioning is ...
We've been using FreeBSD-10 for video streaming website where FreeBSD serves static content (mp4, jpg) over Nginx+php-fpm & performs FFmpeg encoding for users uploaded videos. Server is utilizing 2Gbps realtime port (2 x 1Gbps LACP) and under load we examined bit high percentage of...