Hi there,
This is my first post on the forum
I have just moved from FreeNAS to FreeBSD. All is great and I simply love the flexibility of FreeBSD!
I'm having an issue and I wondered if you can spot what is wrong...
zpool status indicates the zpool is degraded due to one faulty drive with 9 read and 120 write errors.
The problem is these drives are fine. It happens over and over again that I remove the drive, scan it with the manufacturer scantool for defects and no problems are found. I reattach the drive, resilver/scrub it and all is back to normal again.
I'm running the 11.2-RELEASE and use the Avago/LSI3008 HBA in IT-mode using the mpr0 default driver. This driver is the very latest driver from the manufacturer. The card is flashed with the latest firmware:
mpr0: <Avago Technologies (LSI) SAS3008> port 0x7000-0x70ff mem 0xb8640000-0xb864ffff,0xb8600000-0xb863ffff irq 42 at device 0.0 numa-domain 0 on pci9
mpr0: Firmware: 16.00.01.00, Driver: 18.03.00.00-fbsd
mpr0: IOCCapabilities: 7a85c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,MSIXIndex,HostDisc,FastPath,RDPQArray>
The drives are Seagate SATA 10TB-drives. The currently drive in error is:
dmesg | grep -B1 'Serial Number'
da0p2:
serial: ZA21****
model: ATA ST10000NM0016-1T SNB0
dmesg shows this:
Are there any settings you are aware of that can remedy the issue?
* Note: powerd is not running.
* Complete build: https://forums.freenas.org/index.php?threads/xeon-gold-6144-my-first-nas.58422/
Kind Regards,
Rick
This is my first post on the forum
I have just moved from FreeNAS to FreeBSD. All is great and I simply love the flexibility of FreeBSD!
I'm having an issue and I wondered if you can spot what is wrong...
zpool status indicates the zpool is degraded due to one faulty drive with 9 read and 120 write errors.
The problem is these drives are fine. It happens over and over again that I remove the drive, scan it with the manufacturer scantool for defects and no problems are found. I reattach the drive, resilver/scrub it and all is back to normal again.
I'm running the 11.2-RELEASE and use the Avago/LSI3008 HBA in IT-mode using the mpr0 default driver. This driver is the very latest driver from the manufacturer. The card is flashed with the latest firmware:
mpr0: <Avago Technologies (LSI) SAS3008> port 0x7000-0x70ff mem 0xb8640000-0xb864ffff,0xb8600000-0xb863ffff irq 42 at device 0.0 numa-domain 0 on pci9
mpr0: Firmware: 16.00.01.00, Driver: 18.03.00.00-fbsd
mpr0: IOCCapabilities: 7a85c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,MSIXIndex,HostDisc,FastPath,RDPQArray>
The drives are Seagate SATA 10TB-drives. The currently drive in error is:
dmesg | grep -B1 'Serial Number'
da0p2:
serial: ZA21****
model: ATA ST10000NM0016-1T SNB0
dmesg shows this:
Code:
ums1 numa-domain 0 on uhub1
ums1: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 4> on usbus0
ums1: 3 buttons and [Z] coordinates ID=0
(da0:mpr0:0:51:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00 length 0 SMID 268 Aborting command 0xfffffe0001f8e140
mpr0: Sending reset from mprsas_send_abort for target ID 51
mpr0: Unfreezing devq for target ID 51
(da0:mpr0:0:51:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00
(da0:mpr0:0:51:0): CAM status: Command timeout
(da0:mpr0:0:51:0): Retrying command
(da0:mpr0:0:51:0): SYNCHRONIZE CACHE(10). CDB: 35 00 00 00 00 00 00 00 00 00
(da0:mpr0:0:51:0): CAM status: SCSI Status Error
(da0:mpr0:0:51:0): SCSI status: Check Condition
(da0:mpr0:0:51:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
(da0:mpr0:0:51:0): Error 6, Retries exhausted
(da0:mpr0:0:51:0): Invalidating pack
Are there any settings you are aware of that can remedy the issue?
* Note: powerd is not running.
* Complete build: https://forums.freenas.org/index.php?threads/xeon-gold-6144-my-first-nas.58422/
Kind Regards,
Rick