Hi all,
I have two models of HP laptops with 10.1-RELEASE and a hidden wireless AP. I set up the configs etc to use the
AP as per the handbook and at wblock@'s web site.
On the first model HP using wpi(4) everything is fine and wireless access works. On the second model HP which uses iwn(4), the dhclient gives up.
My /etc/rc.conf extract is
My /etc/wpa_supplicant.conf is
It must be seeing the AP because it is seen when scanned.
Running ifconfig(8) -
The problem is not unlike Thread wireless-usage-issue-under-iwn0.40700/ but I just not sure where to go from here or what else to check.
Any thoughts?
Thanks,
Chris.
I have two models of HP laptops with 10.1-RELEASE and a hidden wireless AP. I set up the configs etc to use the
AP as per the handbook and at wblock@'s web site.
On the first model HP using wpi(4) everything is fine and wireless access works. On the second model HP which uses iwn(4), the dhclient gives up.
Code:
# dhclient wlan0
wlan0: no link .............. giving up
My /etc/rc.conf extract is
Code:
wlans_iwn0="wlan0"
ifconfig_wlan0="WPA SYNCDHCP"
My /etc/wpa_supplicant.conf is
Code:
network={
scan_ssid=1
ssid="xxxxxxx"
psk="xxxxxxxxxxx"
}
It must be seeing the AP because it is seen when scanned.
Code:
# ifconfig wlan0 up scan
SSID/MESH ID BSSID CHAN RATE S:N INT CAPS
00:60:64:74:a3:7c 1 54M -70:-95 100 EP HTCAP RSN WME
Running ifconfig(8) -
Code:
# ifconfig
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 68:b5:99:e2:0d:1a
inet 10.1.1.3 netmask 0xffffff00 broadcast 10.1.1.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
iwn0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
ether 8c:a9:82:31:c8:c0
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
status: associated
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 8c:a9:82:31:c8:c0
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
status: no carrier
ssid "" channel 12 (2467 MHz 11g)
country US authmode WPA1+WPA2/802.11i privacy MIXED deftxkey UNDEF
txpower 14 bmiss 10 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250
roam:rssi 7 roam:rate 5 protmode CTS wme roaming MANUAL bintval 0
The problem is not unlike Thread wireless-usage-issue-under-iwn0.40700/ but I just not sure where to go from here or what else to check.
Any thoughts?
Thanks,
Chris.