Hey all,
I am extremely new to BSD but I am trying to tiptoe into it, since I am a little bored with Linux, I figured it might be something semi-interesting to check out.
I tried to boot it up using the default option, and it just hangs almost immediately (roughly 1 second). Here is the output I can see:
I don't think I can scroll up, because when I press a key to abort, the next key I press makes it reboot I think, so sorry if not enough information is shown. I tried single user and the same behavior is exhibited. When I try to boot into safe mode, rather than pulling up the panic dialog, it just freezes as shown below:
I'm still trying to figure out where to start with this, since I can't even get it to boot, haha. I'd greatly appreciate any help or a point in the right direction. Thanks!
I am extremely new to BSD but I am trying to tiptoe into it, since I am a little bored with Linux, I figured it might be something semi-interesting to check out.
I tried to boot it up using the default option, and it just hangs almost immediately (roughly 1 second). Here is the output I can see:
Code:
frame pointer = 0x28:0xffffffff811a5bf0
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, long 1, def32 0, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 0 (swapper)
trap number = 12
panic: page fault
cupid = 0
KDB: stack backtrace:
#0 0xffffffff805f4e0e at kdb_backtrace+0x5e
#1 0xffffffff805c2d07 at panic+0x187
#2 0xffffffff808ac600 at trap_fatal+0x290
#3 0xffffffff808ac9df at trap_pfault+0x28f
#4 0xffffffff808acebf at trap+0x3df
#5 0xffffffff80894fb4 at calltrap+0x8
#6 0xffffffff8088f04f at nexus_acpi_attach+0x7f
#7 0xffffffff805eea09 at device_attach+0x69
#8 0xffffffff805f0316 at bus_generic_new_pass+0xd6
#9 0xffffffff805f002a at bus_set_pass+0x7a
#10 0xffffffff80891c3a at configure+0x77
#11 0xffffffff8057c097 at mi_startup+0x77
#12 0xffffffff8018e09c at btext+0x2c
uptime: 1s
Automatic reboot in 15 seconds - press a key on the console to abort
Code:
pci0: <base peripheral> at device 4.0 (no driver attached)
pci0: <multimedia, audio> at device 5.0 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xf0804000-0xf0804fff irq 11 at device 6.0 on pci0
ohci0: Could not allocate irq
device_attach: ohci0 attach returned 6
pci0: <bridge> at device 7.0 (no driver attached)
ehci0: <Intel 82801FB (ICH6) USB 2.0 controller> mem 0xf0805000-0xf0805fff irq 10 at device 11.0 on pci0
ehci0: Could not allocate irq
device_attach: ehci0 attach returned 6
cpu0 on motherboard
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xe2000,0xe2fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
atrtc0: Warning: Couldn't map Interrupt.
fdc0: cannot reserve interrupt line
ppc0: cannot reserve I/O port range
Timecounter "TSC" frequency 2763283440 Hz quality 800
Timecounters tick every 10.000 msec
md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xffffffff80d9fe20
I'm still trying to figure out where to start with this, since I can't even get it to boot, haha. I'd greatly appreciate any help or a point in the right direction. Thanks!