Radxa Cubie A5E

covacat · Monday at 9:20 AM

I have one but never booted it.
8 x cortex a55, dual ethernet. somewhat cheaper than rk356x.
mine has no emmc
serial console should work but it seems thats it (no clock / pinctrl / anything else support)
at least there is mainline u-boot support.

covacat · Monday at 10:00 AM

covacat said:
at least there is mainline u-boot support

but no arm trusted firmware support

covacat · Monday at 11:01 AM

well, to quote djokovic in italian accent
"Not too baaad"

Code:

cpuid = 0
time = 12
KDB: stack backtrace:
db_trace_self() at db_trace_self
db_trace_self_wrapper() at db_trace_self_wrapper+0x30
vpanic() at vpanic+0x1d4
panic() at panic+0x44
vfs_mountroot() at vfs_mountroot+0x1dd4
start_init() at start_init+0x28
fork_exit() at fork_exit+0x8c
fork_trampoline() at fork_trampoline+0x14
KDB: enter: panic
[ thread pid 1 tid 100002 ]
Stopped at      kdb_enter+0x40: str     xzr, [x19, #640]
db> boot
No such command; use "help" to list available commands
db> reboot
Uptime: 12s

U-Boot SPL 2025.10 (Nov 10 2025 - 12:30:09 +0200)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL31: v2.12.0(debug):b5de74a68
NOTICE:  BL31: Built : 11:57:43, Nov 10 2025
NOTICE:  BL31: Detected Allwinner A523 SoC (1890)
NOTICE:  BL31: Found U-Boot DTB at 0xa0aa990, model: Radxa Cubie A5E
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    Maximum SPI INTID supported: 287
INFO:    Configuring SPC Controller
INFO:    BL31: Platform setup done
INFO:    BL31: Initializing runtime services
INFO:    BL31: cortex_a55: CPU workaround for erratum 1530923 was applied
INFO:    PSCI: Suspend is unavailable
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x4a000000
INFO:    SPSR = 0x3c9


U-Boot 2025.10 (Nov 10 2025 - 12:30:09 +0200) Allwinner Technology

CPU:   Allwinner A523 (SUN55I)
Model: Radxa Cubie A5E
DRAM:  2 GiB
sunxi_set_gate: (CLK#35) unhandled
Core:  77 devices, 22 uclasses, devicetree: separate
WDT:   Not starting watchdog@2050000
MMC:   mmc@4020000: 0
Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
In:    serial@2500000
Out:   serial@2500000
Err:   serial@2500000
Net:   eth0: ethernet@4500000
starting USB...
USB EHCI 1.00
USB OHCI 1.0
USB EHCI 1.00
USB OHCI 1.0
Bus usb@4101000: 1 USB Device(s) found
Bus usb@4101400: 1 USB Device(s) found
Bus usb@4200000: 1 USB Device(s) found
Bus usb@4200400: 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Booting: Label: mmc 0 Device path: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6f00000000000000)/SD(0)/SD(0)
console comconsole failed to initialize
Consoles: EFI console  serial port
    Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p1:
FreeBSD/arm64 EFI loader, Revision 3.0

   Command line arguments: loader.efi
   Image base: 0xbad4c000
   EFI version: 2.110
   EFI Firmware: Das U-Boot (rev 8229.4096)
   Console: efi,comconsole (0)
   Load Path: /\EFI\BOOT\BOOTAA64.EFI
   Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6f00000000000000)/SD(0)/SD(0)/HD(1,GPT,95c8a219-eb17-1743-8356-187f371e9fbc,0xf000,0x200000)
   BootCurrent: 0000
   BootOrder: 0000[*]
   BootInfo Path: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6f00000000000000)/SD(0)/SD(0)
Ignoring Boot0000: Only one DP found
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6f00000000000000)/SD(0)/SD(0)/HD(1,GPT,95c8a219-eb17-1743-8356-187f371e9fbc,0xf000,0x200000)
Setting currdev to disk0p1:
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6f00000000000000)/SD(0)/SD(0)/HD(2,GPT,d16f7845-43ca-d042-a328-9deba0545726,0x20f000,0x1a91000)
Setting currdev to disk0p2:
Loading /boot/defaults/loader.conf
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.local
/
Loading kernel...
/boot/kernel/kernel text=0x2a8 text=0xa94dc0 text=0x2b0f2c data=0x160438 data=0x0+0x2c1000 0x8+0x16bfa8+0x8+0x1971ce|
Loading configured modules...
can't find '/a.dtb'
can't find '/boot/entropy'
can't find '/etc/hostid'

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by EFI at 0xbaee5000.
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance
Copyright (c) 1992-2023 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 14.3-RELEASE GENERIC-DRM arm64
FreeBSD clang version 19.1.7 (https://github.com/llvm/llvm-project.git llvmorg-19.1.7-0-gcd708029e0b2)
VT: init without driver.
module scmi already present!
real memory  = 2147483648 (2048 MB)
avail memory = 2068451328 (1972 MB)
Starting CPU 1 (100)
Starting CPU 2 (200)
Starting CPU 3 (300)
Starting CPU 4 (400)
Starting CPU 5 (500)
Starting CPU 6 (600)
Starting CPU 7 (700)
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller v3.0> mem 0x3400000-0x340ffff,0x3460000-0x355ffff irq 33 on simplebus0
its0: <ARM GIC Interrupt Translation Service> mem 0x3440000-0x345ffff on gic0
its0: Timeout while waiting for CMD completion.
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
generic_timer0: <ARMv8 Generic Timer> irq 1,2,3,4 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
aw_syscon0: <Allwinner syscon> mem 0x3000000-0x3000fff on simplebus0
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0
��]X.��r���standard ns8250 class UART with FIFOs> mem 0x2500000-0x25003ff irq 19 on simplebus0
uart0: console (-1,n,8,1)
musbotg0: <Allwinner USB DRD> mem 0x4100000-0x41003ff irq 34 on simplebus0
device_attach: musbotg0 attach returned 19
ehci0: <Generic EHCI Controller> mem 0x4101000-0x41010ff irq 35 on simplebus0
usbus0: EHCI version 1.0
usbus0 on ehci0
ohci0: <Generic OHCI Controller> mem 0x4101400-0x41014ff irq 36 on simplebus0
usbus1 on ohci0
ehci1: <Generic EHCI Controller> mem 0x4200000-0x42000ff irq 37 on simplebus0
usbus2: EHCI version 1.0
usbus2 on ehci1
ohci1: <Generic OHCI Controller> mem 0x4200400-0x42004ff irq 38 on simplebus0
usbus3 on ohci1
awg0: <Allwinner Gigabit Ethernet> mem 0x4500000-0x450ffff irq 39 on simplebus0
awg0: cannot get ahb reset
device_attach: awg0 attach returned 2
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iichb0: could not find clock
device_attach: iichb0 attach returned 19
armv8crypto0: <AES-CBC,AES-XTS,AES-GCM>
Timecounters tick every 1.000 msec
CPU  0: ARM Cortex-A55 r2p0 affinity:  0  0
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG>
 Instruction Set Attributes 0 = <DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL>
 Instruction Set Attributes 1 = <RCPC-8.3,DCPoP>
 Instruction Set Attributes 2 = <>
         Processor Features 0 = <RAS,GIC,AdvSIMD+HP,FP+HP,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <PSTATE.SSBS>
         Processor Features 2 = <>
      Memory Model Features 0 = <TGran4,TGran64,TGran16,SNSMem,BigEnd,16bit ASID,1TB PA>
      Memory Model Features 1 = <XNX,PAN+ATS1E1,LO,HPD+TTPBHA,VH,16bit VMID,HAF+DS>
      Memory Model Features 2 = <32bit CCIDX,48bit VA,IESB,UAO,CnP>
      Memory Model Features 3 = <>
      Memory Model Features 4 = <>
             Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3p1,Debugv8p2>
             Debug Features 1 = <>
         Auxiliary Features 0 = <>
         Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <RDM,CRC32,SHA2,SHA1,AES+VMULL,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP Arith,SIMDHP Arith,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU  1: ARM Cortex-A55 r2p0 affinity:  1  0
CPU  2: ARM Cortex-A55 r2p0 affinity:  2  0
CPU  3: ARM Cortex-A55 r2p0 affinity:  3  0
CPU  4: ARM Cortex-A55 r2p0 affinity:  4  0
CPU  5: ARM Cortex-A55 r2p0 affinity:  5  0
CPU  6: ARM Cortex-A55 r2p0 affinity:  6  0
CPU  7: ARM Cortex-A55 r2p0 affinity:  7  0
gic0: using for IPIs
Release APs...done
usbus0: 480Mbps High Speed USB v2.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
TCP_ratelimit: Is now initialized
ugen0.1: <Generic EHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Generic OHCI root HUB> at usbus1
ugen2.1: <Generic EHCI root HUB> at usbus2
ugen3.1: <Generic OHCI root HUB> at usbus3
uhub1 on usbus1
uhub2 on usbus3
uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
uhub2: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
uhub3 on usbus2
uhub3: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
uhub2: 1 port with 1 removable, self powered
uhub1: 1 port with 1 removable, self powered
uhub0: 1 port with 1 removable, self powered
uhub3: 1 port with 1 removable, self powered

Loader variables:

Manual root filesystem specification:
  <fstype>:<device> [options]
      Mount <device> using filesystem <fstype>
      and with the specified (optional) option list.

    eg. ufs:/dev/da0s1a
        zfs:zroot/ROOT/default
        cd9660:/dev/cd0 ro
          (which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /)

  ?               List valid disk boot devices
  .               Yield 1 second (for background tasks)
  <empty line>    Abort manual input

mountroot> random: unblocking device.

covacat · Monday at 11:10 AM

blackbird9 · Monday at 10:12 PM

That's a neat little board. Very useful. Dual ethernet is interesting.

Phishfry · Monday at 10:20 PM

I wonder why they chose the Cubie name. The original Cubie was not Radxa right? CubieTruck or something.
Maybe the connectors are in the same spot?

Cubieboard - Wikipedia

en.wikipedia.org

covacat · Monday at 10:55 PM

dunno, they may have bought the original cubiestuff maker. it's also using allwinner soc.
ill try to add clocks and pinctrl/gpio, power ic support.
if i can get ethernet and sd card working it will be cool

covacat · 2025-11-14T10:35:16+0000

got clocks, gpio, network
sd card works like shit

Code:

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by EFI at 0xbaee5000.
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance
Copyright (c) 1992-2023 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 14.3-RELEASE GENERIC-DRM arm64
FreeBSD clang version 19.1.7 (https://github.com/llvm/llvm-project.git llvmorg-19.1.7-0-gcd708029e0b2)
VT: init without driver.
module scmi already present!
real memory  = 2147483648 (2048 MB)
avail memory = 2068365312 (1972 MB)
Starting CPU 1 (100)
Starting CPU 2 (200)
Starting CPU 3 (300)
Starting CPU 4 (400)
Starting CPU 5 (500)
Starting CPU 6 (600)
Starting CPU 7 (700)
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
aw_rtc0: <Allwinner RTC> mem 0x7090000-0x70903ff irq 44 on simplebus0
aw_rtc0: Now i have the 'hosc'
aw_rtc0: registered as a time-of-day clock, resolution 1.000000s
ccu_a523ng0: <Allwinner A523 Clock Control Unit NG> mem 0x2001000-0x2001fff on simplebus0
ccu_sun55i_a523_r0: <Allwinner A523 Clock Control Unit NG> mem 0x7010000-0x701024f on simplebus0
gic0: <ARM Generic Interrupt Controller v3.0> mem 0x3400000-0x340ffff,0x3460000-0x355ffff irq 33 on simplebus0
its0: <ARM GIC Interrupt Translation Service> mem 0x3440000-0x345ffff on gic0
its0: Timeout while waiting for CMD completion.
gpio0: <Allwinner GPIO/Pinmux controller> mem 0x2000000-0x20007ff irq 5,6,7,8,9,10,11,12,13,14 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Allwinner GPIO/Pinmux controller> mem 0x7022000-0x70227ff irq 41,42 on simplebus0
gpiobus1: <OFW GPIO bus> on gpio1
iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x7081400-0x70817ff irq 43 on simplebus0
iicbus0: <OFW I2C bus> on iichb0
generic_timer0: <ARMv8 Generic Timer> irq 1,2,3,4 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
aw_syscon0: <Allwinner syscon> mem 0x3000000-0x3000fff on simplebus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0
gpioc0: <GPIO controller> on gpio0
aw_mmc0: <Allwinner Integrated MMC/SD controller> mem 0x4020000-0x4020fff irq 15 on simplebus0
uart0: <Non-standard ns8250 class UART with FIFOs> mem 0x2500000-0x25003ff irq 19 on simplebus0
uart0: console (115384,n,8,1)
musbotg0: <Allwinner USB DRD> mem 0x4100000-0x41003ff irq 34 on simplebus0
usbus0: Dynamic FIFO sizing detected, assuming 16Kbytes of FIFO RAM
usbus0 on musbotg0
ehci0: <Generic EHCI Controller> mem 0x4101000-0x41010ff irq 35 on simplebus0
usbus1: EHCI version 1.0
usbus1 on ehci0
ohci0: <Generic OHCI Controller> mem 0x4101400-0x41014ff irq 36 on simplebus0
usbus2 on ohci0
ehci1: <Generic EHCI Controller> mem 0x4200000-0x42000ff irq 37 on simplebus0
usbus3: EHCI version 1.0
usbus3 on ehci1
ohci1: <Generic OHCI Controller> mem 0x4200400-0x42004ff irq 38 on simplebus0
usbus4 on ohci1
awg0: <Allwinner Gigabit Ethernet> mem 0x4500000-0x450ffff irq 39 on simplebus0
miibus0: <MII bus> on awg0
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
awg0: Ethernet address: 02:10:2c:3f:ba:eb
gpioc1: <GPIO controller> on gpio1
iicbus0: <unknown card> at addr 0x68
iicbus0: <unknown card> at addr 0x6c
iic0: <I2C generic I/O> on iicbus0
armv8crypto0: <AES-CBC,AES-XTS,AES-GCM>
Timecounters tick every 1.000 msec
CPU  0: ARM Cortex-A55 r2p0 affinity:  0  0
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG>
 Instruction Set Attributes 0 = <DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL>
 Instruction Set Attributes 1 = <RCPC-8.3,DCPoP>
 Instruction Set Attributes 2 = <>
         Processor Features 0 = <RAS,GIC,AdvSIMD+HP,FP+HP,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <PSTATE.SSBS>
         Processor Features 2 = <>
      Memory Model Features 0 = <TGran4,TGran64,TGran16,SNSMem,BigEnd,16bit ASID,1TB PA>
      Memory Model Features 1 = <XNX,PAN+ATS1E1,LO,HPD+TTPBHA,VH,16bit VMID,HAF+DS>
      Memory Model Features 2 = <32bit CCIDX,48bit VA,IESB,UAO,CnP>
      Memory Model Features 3 = <>
      Memory Model Features 4 = <>
             Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3p1,Debugv8p2>
             Debug Features 1 = <>
         Auxiliary Features 0 = <>
         Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <RDM,CRC32,SHA2,SHA1,AES+VMULL,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP Arith,SIMDHP Arith,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU  1: ARM Cortex-A55 r2p0 affinity:  1  0
CPU  2: ARM Cortex-A55 r2p0 affinity:  2  0
CPU  3: ARM Cortex-A55 r2p0 affinity:  3  0
CPU  4: ARM Cortex-A55 r2p0 affinity:  4  0
CPU  5: ARM Cortex-A55 r2p0 affinity:  5  0
CPU  6: ARM Cortex-A55 r2p0 affinity:  6  0
CPU  7: ARM Cortex-A55 r2p0 affinity:  7  0
gic0: using for IPIs
Release APs...usbus0: 480Mbps High Speed USB v2.0
done
usbus1: 480Mbps High Speed USB v2.0
usbus2: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
Trying to mount root from ufs:/dev/ufs/FreeBSD_Install [ro,noatime]...
TCP_ratelimit: Is now initialized
ugen0.1: <Mentor Graphics OTG Root HUB> at usbus0
ugen1.1: <Generic EHCI root HUB> at usbus1
ugen4.1: <Generic OHCI root HUB> at usbus4
ugen2.1: <Generic OHCI root HUB> at usbus2
ugen3.1: <Generic EHCI root HUB> at usbus3
uhub0 on usbus0
uhub1 on usbus1
uhub2 on usbus3
uhub3 on usbus2
uhub2: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
uhub0: <Mentor Graphics OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
uhub4 on usbus4
uhub3: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
uhub4: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
uhub1: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
uhub4: 1 port with 1 removable, self powered
uhub3: 1 port with 1 removable, self powered
mmc0: <MMC/SD bus> on aw_mmc0
mmcsd0: 16GB <SDHC   0.0 SN 0000008D MFG 10/2021 by 69 -B> at mmc0 0.4MHz/4bit/4096-block
mmc0: Failed to set VCCQ for card at relative address 1
uhub0: 1 port with 1 removable, self powered
GEOM: mmcsd0: the primary GPT table is corrupt or invalid.
GEOM: mmcsd0: using the secondary instead -- recovery strongly advised.
GEOM: diskid/DISK-0000008D: the primary GPT table is corrupt or invalid.
GEOM: diskid/DISK-0000008D: using the secondary instead -- recovery strongly advised.
uhub2: 1 port with 1 removable, self powered
uhub1: 1 port with 1 removable, self powered

covacat · 2025-11-14T10:40:53+0000

need to fix the regulators now
writing ccu drivers is a kind of modern torture
and the linux gang seems to add more crap every time they get a chance
why the fsck can't they use the same names for clocks as in the soc manual
fscking hosc losc iosc

blackbird9 · 2025-11-14T11:50:22+0000

hahaha

Maybe try a different sd card?

covacat · 2025-11-14T12:10:39+0000

its not the card itself, its something wrong with the driver
high speed timings do not work at all and i commented some code out and now it works like a better floppy and readonly

the networks seems to work well

Radxa Cubie A5E

Attachments