root@FreeBSD:~ # cu -l /dev/cuaU0 -s 115200
Connected
-- NAS EXPLORER --
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** QSI BOARD: NAS-PLUG LE
U-Boot 1.1.4 (Sep 26 2011 - 13:01:13) Marvell version: 3.4.27
QSI NAS version: 1.0.6
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:NAND READID : MID=0x98, DID=0xda
256 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 3 2 1 0
NAND read: device 0 offset 0x100000, size 0x600000
Reading data from 0x6ff800 -- 100% complete.
6291456 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2010-06-17 5:37:59 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2095148 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.18 (ramang@es5x86.axentra.com) (gcc version 4.3.2 (sdk3.2rc1-ct-ng-1.4.1) ) #16 Thu Jun 17 01:37:53 EDT 2010
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 32512
Kernel command line: console=ttyS0,115200 ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 125568KB available (3844K code, 261K data, 128K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_4.3.4_patch22)-- SHEEVA PLUG Soc: 88F6281 A1 LE
Detected Tclk 200000000 and SysClk 400000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c057b600
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: kw_clocksource clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
RTC registered
XOR registered 2 channels
XOR 2nd invalidate WA enabled
cesadev_init(c0011854)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
MV Buttons Driver Load
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload enabled
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Network Fast Processing (Routing) supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Proc tool API enabled
o SKB Reuse supported
o SKB Recycle supported
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o register under eth%d platform
o eth0, ifindex = 1, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (c7da7000): 1024 entries, 4096 bytes
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0x98, Chip ID: 0xda (Toshiba NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00100000 : "u-boot"
0x00100000-0x00700000 : "uImage"
0x00700000-0x10000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd2 to ubi0
UBI: MTD device name: "root"
UBI: MTD device size: 249 MiB
UBI: number of good PEBs: 1992
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 1992
UBI: number of PEBs reserved for bad PEB handling: 38
UBI: max/mean erase counter: 1/0
UBI: background thread "ubi_bgt0d" started, PID 296
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
usb 1-1: new high speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Linux telephony interface: v1.00
Marvell Telephony Driver:
Warning Tdm is Powered Off
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 91 MB/s
raid6: int32x2 109 MB/s
raid6: int32x4 119 MB/s
raid6: int32x8 94 MB/s
raid6: using algorithm int32x4 (119 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
arm4regs : 1084.400 MB/sec
8regs : 822.000 MB/sec
32regs : 803.200 MB/sec
raid5: using function: arm4regs (1084.400 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 239857664 bytes (234236 KiB, 228 MiB, 1889 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: 4 (latest is 4)
UBIFS: default compressor: zlib
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem).
Freeing init memory: 128K
Failed to execute /linuxrc. Attempting defaults...
INIT: version 2.86 booting
Welcome to HipServ
Press 'I' to enter interactive startup.
Setting clock : Tue Nov 21 19:08:00 GMT 2017 [ OK ]
Starting udev: [ OK ]
Setting hostname axentraserver.balanga-gfh.seagateshare.com: [ OK ]
Setting up Logical Volume Management: No volume groups found
[ OK ]
Checking filesystems
Checking all file systems.
[ OK ]
Mounting local filesystems: mount: sysfs already mounted or /sys busy
mount: according to mtab, /sys is already mounted on /sys
[FAILED]
Enabling /etc/fstab swaps: [ OK ]
INIT: Entering runlevel: 3
Entering non-interactive startup
HipServ startup:[ OK ]
Starting reset: [ OK ]
Starting seagate-lifecycle:[ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0... done.
/etc/init.d/iptables: line 42: /etc/sysconfig/networking/oe-profiles/default/ifcfg-eth0: No such file or directory
Flushing all current rules and user defined chains: [ OK ]
Clearing all current rules and user defined chains: [ OK ]
[ OK ]
[ OK ]
Applying iptables firewall rules:
[ OK ]
[ OK ]
check_igd.pl: no process killed
Starting igd-daemon:sh: /usr/sbin/oe-gateway-check: No such file or directory
[ OK ]
error reading information on service transmission.init: No such file or directory
[ OK ]
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting locator:[ OK ]
Starting system message bus: [ OK ]
Starting sshd: [ OK ]
Starting cups: [ OK ]
Starting vsftpd for vsftpd: [ OK ]
Starting httpd: [ OK ]
Starting appserver: [ OK ]
Starting crond: [ OK ]
Starting Netatalk services:
Starting cnid_metad:[ OK ]
Starting afpd:[ OK ]
Starting SMB services: [ OK ]
Starting NMB services: [ OK ]
Starting OEone System Proxy: SPD starting....log level=1, uid=0
[ OK ]
Starting access-patrol:[ OK ]
Starting Avahi daemon... [ OK ]
Starting /usr/sbin/minidlna ...
Starting S99lld2: [ OK ]
0
Starting DAAP server: [ OK ]
Starting mynetworkd:[ OK ]
HipServ - Checking if RAID needs to be rebuilt
HipServ - No RAID found
HipServ - Bringing up iptables
HipServ - Updating date...
[ OK ]
success
HipServ - Enabling swap
HipServ - Cleaning USB mountpoints
HipServ - Mounting USB devices
ufsd: module license 'Commercial product' taints kernel.
ufsd: driver 8.4 (011_A) LBD=ON with ioctl loaded at bf04b000
NTFS read/write support included
NTFS includes 4K MBR support for device with sector size 512
Hfs+/HfsX read/write support included
Built for: seagate_axentra_512_COMBO
HipServ - Checking for FTPS certificate
HipServ - Found vsftpd key file
HipServ - Ensuring that table structures are up-to-date
HipServ - Starting usbreaderd: [ OK ]
HipServ - Checking for updates...
[ OK ]
success
HipServ - boot complete
Starting spindownd.init: [ OK ]
Starting xMySyncMount.php: [ OK ]
axentraserver.balanga-gfh.seagateshare.com login: