root@bsdserver:/usr/home/anders # smartctl -x /dev/da3
smartctl 6.4 2015-06-04 r4109 [FreeBSD 10.2-RELEASE-p8 amd64] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WCC4MLJE7KVK
LU WWN Device Id: 5 0014ee 2b5905761
Firmware Version: 82.00A82
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Feb 15 09:31:32 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unknown
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (26940) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off supp ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 272) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 69
3 Spin_Up_Time POS--K 198 172 021 - 3066
4 Start_Stop_Count -O--CK 100 100 000 - 155
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 5
9 Power_On_Hours -O--CK 087 087 000 - 9770
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 154
192 Power-Off_Retract_Count -O--CK 200 200 000 - 141
193 Load_Cycle_Count -O--CK 200 200 000 - 1518
194 Temperature_Celsius -O---K 119 105 000 - 28
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 2
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 46 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 46 [21] occurred at disk power-on lifetime: 9758 hours (406 days + 14 hour s)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 98 e8 9a 70 40 00 Error: WP at LBA = 0x98e89a70 = 256538 0720
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 f0 00 10 00 00 98 e8 98 70 40 00 00:13:27.760 WRITE FPDMA QUEUED
61 01 00 00 10 00 00 98 e8 97 70 40 00 00:13:27.759 WRITE FPDMA QUEUED
61 00 10 00 10 00 00 98 e8 99 60 40 00 00:13:27.759 WRITE FPDMA QUEUED
61 00 10 00 10 00 00 06 40 02 b8 40 00 00:13:27.743 WRITE FPDMA QUEUED
60 01 00 00 08 00 00 98 e8 9a 70 40 00 00:13:27.743 READ FPDMA QUEUED
Error 45 [20] occurred at disk power-on lifetime: 9758 hours (406 days + 14 hour s)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 98 e8 99 70 40 00 Error: WP at LBA = 0x98e89970 = 256538 0464
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 00 06 40 02 b8 40 00 00:13:23.640 WRITE FPDMA QUEUED
60 00 10 00 10 00 00 06 40 02 b8 40 00 00:13:23.625 READ FPDMA QUEUED
60 01 00 00 08 00 00 98 e8 9a 70 40 00 00:13:23.625 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 99 70 40 00 00:13:23.625 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 00 00:13:23.619 READ LOG EXT
Error 44 [19] occurred at disk power-on lifetime: 9758 hours (406 days + 14 hour s)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 98 e8 99 70 40 00 Error: WP at LBA = 0x98e89970 = 256538 0464
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 00 e8 e0 82 b8 40 00 00:13:20.020 WRITE FPDMA QUEUED
61 00 10 00 18 00 00 e8 e0 84 b8 40 00 00:13:20.014 WRITE FPDMA QUEUED
60 00 10 00 20 00 00 06 40 02 b8 40 00 00:13:19.987 READ FPDMA QUEUED
60 00 10 00 18 00 00 e8 e0 84 b8 40 00 00:13:19.987 READ FPDMA QUEUED
60 00 10 00 10 00 00 e8 e0 82 b8 40 00 00:13:19.987 READ FPDMA QUEUED
Error 43 [18] occurred at disk power-on lifetime: 9758 hours (406 days + 14 hour s)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 98 e8 99 70 40 00 Error: UNC at LBA = 0x98e89970 = 25653 80464
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 10 00 20 00 00 06 40 02 b8 40 00 00:13:16.040 READ FPDMA QUEUED
60 00 10 00 18 00 00 e8 e0 84 b8 40 00 00:13:16.040 READ FPDMA QUEUED
60 00 10 00 10 00 00 e8 e0 82 b8 40 00 00:13:16.040 READ FPDMA QUEUED
60 01 00 00 08 00 00 98 e8 9a 70 40 00 00:13:16.040 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 99 70 40 00 00:13:16.040 READ FPDMA QUEUED
Error 42 [17] occurred at disk power-on lifetime: 9758 hours (406 days + 14 hour s)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 98 e8 97 b0 40 00 Error: UNC at LBA = 0x98e897b0 = 25653 80016
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 08 00 00 98 e8 98 70 40 00 00:13:09.040 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 97 70 40 00 00:13:09.040 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 00 00:13:09.036 READ LOG EXT
60 01 00 00 08 00 00 98 e8 98 70 40 00 00:13:02.041 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 97 70 40 00 00:13:02.041 READ FPDMA QUEUED
Error 41 [16] occurred at disk power-on lifetime: 9758 hours (406 days + 14 hour s)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 98 e8 97 97 40 00 Error: UNC at LBA = 0x98e89797 = 25653 79991
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 08 00 00 98 e8 98 70 40 00 00:13:02.041 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 97 70 40 00 00:13:02.041 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 00 00:13:02.036 READ LOG EXT
60 01 00 00 08 00 00 98 e8 98 70 40 00 00:12:55.636 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 97 70 40 00 00:12:55.636 READ FPDMA QUEUED
Error 40 [15] occurred at disk power-on lifetime: 9758 hours (406 days + 14 hour s)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 98 e8 97 90 40 00 Error: UNC at LBA = 0x98e89790 = 25653 79984
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 08 00 00 98 e8 98 70 40 00 00:12:55.636 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 97 70 40 00 00:12:55.636 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 00 00:12:55.632 READ LOG EXT
60 01 00 00 08 00 00 98 e8 98 70 40 00 00:12:48.637 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 97 70 40 00 00:12:48.636 READ FPDMA QUEUED
Error 39 [14] occurred at disk power-on lifetime: 9758 hours (406 days + 14 hour s)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 98 e8 97 97 40 00 Error: UNC at LBA = 0x98e89797 = 25653 79991
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 08 00 00 98 e8 98 70 40 00 00:12:48.637 READ FPDMA QUEUED
60 01 00 00 00 00 00 98 e8 97 70 40 00 00:12:48.636 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 00 00:12:48.632 READ LOG EXT
61 00 f0 00 08 00 00 98 e8 96 70 40 00 00:12:41.987 WRITE FPDMA QUEUED
61 01 00 00 08 00 00 98 e8 95 70 40 00 00:12:41.987 WRITE FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 28 Celsius
Power Cycle Min/Max Temperature: 28/37 Celsius
Lifetime Min/Max Temperature: 19/42 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (261)
Index Estimated Time Temperature Celsius
262 2016-02-15 01:34 28 *********
... ..(476 skipped). .. *********
261 2016-02-15 09:31 28 *********
SMART WRITE LOG does not return COUNT and LBA_LOW register
SCT (Get) Error Recovery Control command failed
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 7 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 44895 Vendor specific
root@bsdserver:/usr/home/anders #
