I recently upgraded my trusty old 4.x system to 8.1 and the one little bit I can't get working is the internal ISA modem in the system. On 4.x it was detected automatically by the sio driver:
But it doesn't show up with the new uart driver. I tried adding the bits for it to device.hints and it shows up, but isn't correctly detected and fails to function. I've tried having the modem set to full PnP and to fixed specification with no change in results.
dmesg contains a few lines like this which may be related:
pnpinfo spews this:
I tried to compile the old sio driver into the kernel, but that fails:
Any pointers for getting this working?
Code:
/kernel: sio4: <U.S. Robotics Sportster 33600 FAX/Voice Int> at port 0x3e8-0x3ef irq 5 on isa0
Sep 27 12:55:32 sinat /kernel: sio4: type 16550A
But it doesn't show up with the new uart driver. I tried adding the bits for it to device.hints and it shows up, but isn't correctly detected and fails to function. I've tried having the modem set to full PnP and to fixed specification with no change in results.
dmesg contains a few lines like this which may be related:
Code:
PnP device failed to report resource data
pnpinfo spews this:
Code:
Checking for Plug-n-Play devices...
Card assigned CSN #1
Vendor ID USR0011 (0x11007256), Serial Number 0x20300104
PnP Version 1.0, Vendor Version 0
Device Description: U.S. Robotics Sportster 33600 FAX/Voice Int
Logical Device ID: USR0006 0x06007256 #0
TAG Start DF
Good Configuration
FIXED I/O base address 0x2f8 length 0x8
IRQ: 3 - only one type (true/edge)
TAG Start DF
Acceptable Configuration
FIXED I/O base address 0x3f8 length 0x8
IRQ: 4 - only one type (true/edge)
TAG Start DF
Acceptable Configuration
FIXED I/O base address 0x3e8 length 0x8
IRQ: 3 4 5 7 - only one type (true/edge)
TAG Start DF
Acceptable Configuration
FIXED I/O base address 0x2e8 length 0x8
IRQ: 3 4 5 7 - only one type (true/edge)
TAG End DF
End Tag
Successfully got 16 resources, 1 logical fdevs
-- card select # 0x0001
CSN USR0011 (0x11007256), Serial Number 0x20300104
Logical device #0
IO: 0x03e8 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 5 0
DMA 4 4
IO range check 0x00 activate 0x01
I tried to compile the old sio driver into the kernel, but that fails:
Code:
/usr/src/sys/dev/sio/sio.c: In function 'sysctl_machdep_comdefaultrate':
/usr/src/sys/dev/sio/sio.c:356: error: 'struct tty' has no member named 't_init_in'
/usr/src/sys/dev/sio/sio.c:356: error: 'struct tty' has no member named 't_init_in'
/usr/src/sys/dev/sio/sio.c:357: error: 'struct tty' has no member named 't_lock_in'
/usr/src/sys/dev/sio/sio.c:357: error: 'struct tty' has no member named 't_lock_in'
/usr/src/sys/dev/sio/sio.c:358: error: 'struct tty' has no member named 't_init_out'
/usr/src/sys/dev/sio/sio.c:358: error: 'struct tty' has no member named 't_init_out'
/usr/src/sys/dev/sio/sio.c:359: error: 'struct tty' has no member named 't_lock_out'
/usr/src/sys/dev/sio/sio.c:359: error: 'struct tty' has no member named 't_lock_out'
/usr/src/sys/dev/sio/sio.c:361: error: 'struct tty' has no member named 't_state'
/usr/src/sys/dev/sio/sio.c:361: error: 'TS_ISOPEN' undeclared (first use in this function)
/usr/src/sys/dev/sio/sio.c:361: error: (Each undeclared identifier is reported only once
/usr/src/sys/dev/sio/sio.c:361: error: for each function it appears in.)
...
Any pointers for getting this working?