Hi all,
I just got this Zotac zbox 323 nano, wanted to install FreeBSD or a NAS version on it.
An USB-Stick with FreeBSD 11.1 boots successfully.
A NAS4Free Stick with version 10.x did boot.
Doing an update on that, failed to boot.
They just renamed their project, so the image I used is called XigmaNAS-x64-embedded-11.2.0.4.5748.
Using the option "failsafe", got some output, it started to boot, the last messages had been:
The other attempts, using a stick to update from FreeBSD 11.1 to 11.2, or a newly downloaded FreeBSD-11.2-RELEASE-amd64-mini-memstick.img image did not get further than:
Here from running FreeBSD 11.1 the dmesg, lspci, lsusb, if that is of any help:
Thanks in advance
I just got this Zotac zbox 323 nano, wanted to install FreeBSD or a NAS version on it.
An USB-Stick with FreeBSD 11.1 boots successfully.
A NAS4Free Stick with version 10.x did boot.
Doing an update on that, failed to boot.
They just renamed their project, so the image I used is called XigmaNAS-x64-embedded-11.2.0.4.5748.
Using the option "failsafe", got some output, it started to boot, the last messages had been:
Code:
...
atrtc0: <AT realtime clock> at port 0x70 irq8 on isa0
atrtc0: registered as a time-of-day-clock, resolution 1.000000s
atrtc0: Can't map interrupt
atrtc0: <AT timer> at port 0x40 on isa0
Timecounter "i8254" frequency 1193182 Hz quality 0
attimer0: Can't map interrupt
fdc0: cannot reserve interrupt line
ppc0: cannot reserve I/O port range
...
panic: no usable event timer found!
The other attempts, using a stick to update from FreeBSD 11.1 to 11.2, or a newly downloaded FreeBSD-11.2-RELEASE-amd64-mini-memstick.img image did not get further than:
Code:
/boot/kernel/kernel ...
Booting...
/
_
Code:
user@machine:~ % dmesg
Copyright (c) 1992-2017 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.1-RELEASE-p11 #0: Thu Jun 21 03:46:08 UTC 2018
root@amd64-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC amd64
FreeBSD clang version 4.0.0 (tags/RELEASE_400/final 297347) (based on LLVM 4.0.0)
VT(vga): resolution 640x480
CPU: Intel(R) Celeron(R) CPU N3150 @ 1.60GHz (1600.05-MHz K8-class CPU)
Origin="GenuineIntel" Id=0x406c3 Family=0x6 Model=0x4c Stepping=3
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x43d8e3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,TSCDLT,AESNI,RDRAND>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x101<LAHF,Prefetch>
Structured Extended Features=0x2282<TSCADJ,SMEP,ERMS,NFPUSG>
VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 8134418432 (7757 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I >
WARNING: L1 data cache covers less APIC IDs than a core
0 < 1
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
random: unblocking device.
ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/32 (20170303/tbfadt-748)
ioapic0 <Version 2.0> irqs 0-114 on motherboard
SMP: AP CPU #3 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
Timecounter "TSC" frequency 1600052620 Hz quality 1000
random: entropy device external interface
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff80f5ec40, 0) error 19
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
nexus0
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
aesni0: <AES-CBC,AES-XTS,AES-GCM,AES-ICM> on motherboard
acpi0: <ALASKA A M I > on motherboard
acpi0: Power Button (fixed)
unknown: I/O range not supported
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0x80000000-0x80ffffff,0x90000000-0x9fffffff irq 16 at device 2.0 on pci0
vgapci0: Boot video device
sdhci_pci0: <Intel Braswell eMMC 4.5.1 Controller> mem 0x81516000-0x81516fff irq 16 at device 16.0 on pci0
sdhci_pci0: 1 slot(s) allocated
mmc0: <MMC/SD bus> on sdhci_pci0
ahci0: <AHCI SATA controller> port 0xf060-0xf07f mem 0x81515000-0x815157ff irq 19 at device 19.0 on pci0
ahci0: AHCI v1.31 with 2 6Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
xhci0: <Intel Braswell USB 3.0 controller> mem 0x81500000-0x8150ffff irq 20 at device 20.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
usbus0 on xhci0
usbus0: 5.0Gbps Super Speed USB v3.0
pci0: <encrypt/decrypt> at device 26.0 (no driver attached)
hdac0: <Intel (0x2284) HDA Controller> mem 0x81510000-0x81513fff irq 22 at device 27.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pcib1: [GIANT-LOCKED]
pcib2: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pcib2: [GIANT-LOCKED]
pci1: <ACPI PCI bus> on pcib2
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0x81400000-0x81400fff,0xa0100000-0xa0103fff irq 17 at device 0.0 on pci1
re0: Using 1 MSI-X message
re0: turning off MSI enable bit.
re0: Chip rev. 0x4c000000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8251 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: 00:01:2e:70:c5:f2
re0: netmap queues/slots: TX 1/256, RX 1/256
pcib3: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pci2: <ACPI PCI bus> on pcib3
re1: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xd000-0xd0ff mem 0x81300000-0x81300fff,0xa0000000-0xa0003fff irq 18 at device 0.0 on pci2
re1: Using 1 MSI-X message
re1: turning off MSI enable bit.
re1: Chip rev. 0x4c000000
re1: MAC rev. 0x00000000
miibus1: <MII bus> on re1
rgephy1: <RTL8251 1000BASE-T media interface> PHY 1 on miibus1
rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re1: Using defaults for TSO: 65518/35/2048
re1: Ethernet address: 00:01:2e:70:c5:f3
re1: netmap queues/slots: TX 1/256, RX 1/256
pcib4: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pci3: <ACPI PCI bus> on pcib4
pci3: <network> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
orm0: <ISA Option ROMs> at iomem 0xd0000-0xd0fff,0xd1000-0xd1fff on isa0
ppc0: cannot reserve I/O port range
uart1: <16550 or compatible> at port 0x2f8 irq 3 on isa0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
nvme cam probe device init
ugen0.1: <0x8086 XHCI root HUB> at usbus0
uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
mmc0: No compatible cards found on bus
hdacc0: <Realtek ALC892 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC892 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC892 (Left Analog)> at nid 20 and 24 on hdaa0
ada0 at ahcich1 bus 0 scbus1 target 0 lun 0
ada0: <HGST HTS541010A9E680 JA0OA560> ATA8-ACS SATA 3.x device
ada0: Serial Number xxxx
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 953869MB (1953525168 512 byte sectors)
pcm1: <Realtek ALC892 (Left Digital)> at nid 30 on hdaa0
hdacc1: <Intel (0x2883) HDA CODEC> at cad 2 on hdac0
hdaa1: <Intel (0x2883) Audio Function Group> at nid 1 on hdacc1
pcm2: <Intel (0x2883) (HDMI/DP 8ch)> at nid 7 on hdaa1
pcm3: <Intel (0x2883) (HDMI/DP 8ch)> at nid 5 on hdaa1
pcm4: <Intel (0x2883) (HDMI/DP 8ch)> at nid 6 on hdaa1
Trying to mount root from zfs:zpool-test/ROOT/11.1p11 []...
uhub0: 13 ports with 13 removable, self powered
ugen0.2: <vendor 0x1a40 USB 2.0 Hub> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x1a40 USB 2.0 Hub, class 9/0, rev 2.00/1.11, addr 1> on usbus0
uhub1: 4 ports with 4 removable, self powered
ugen0.3: <Generic USB2.0-CRW> at usbus0
umass0 on uhub1
umass0: <Bulk-In, Bulk-Out, Interface> on usbus0
umass0: SCSI over Bulk-Only; quirks = 0x4000
umass0:2:0: Attached to scbus2
da0 at umass-sim0 bus 0 scbus2 target 0 lun 0
da0: <Generic- SD/MMC/MS PRO 1.00> Removable Direct Access SPC-2 SCSI device
da0: Serial Number xxxx
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
da0: quirks=0x2<NO_6_BYTE>
ugen0.4: <vendor 0x8087 product 0x07dc> at usbus0
ugen0.5: <vendor 0x1a40 USB 2.0 Hub> at usbus0
uhub2 on uhub1
uhub2: <vendor 0x1a40 USB 2.0 Hub, class 9/0, rev 2.00/1.11, addr 4> on usbus0
uhub2: 4 ports with 4 removable, self powered
ugen0.6: <vendor 0x04f3 product 0x0103> at usbus0
ukbd0 on uhub2
ukbd0: <vendor 0x04f3 product 0x0103, class 0/0, rev 2.00/1.07, addr 5> on usbus0
kbd2 at ukbd0
umass1 on uhub1
umass1: <SanDisk Extreme, class 0/0, rev 2.10/0.10, addr 6> on usbus0
umass1: SCSI over Bulk-Only; quirks = 0x0100
umass1:3:1: Attached to scbus3
da1 at umass-sim1 bus 1 scbus3 target 0 lun 0
da1: <SanDisk Extreme 0001> Removable Direct Access SPC-4 SCSI device
da1: Serial Number xxx
da1: 40.000MB/s transfers
da1: 30533MB (62533296 512 byte sectors)
da1: quirks=0x2<NO_6_BYTE>
re0: link state changed to UP
re1: link state changed to DOWN
uhid0 on uhub2
uhid0: <vendor 0x04f3 product 0x0103, class 0/0, rev 2.00/1.07, addr 5> on usbus0
Accounting enabled
re0: link state changed to DOWN
re0: link state changed to UP
user@machine:~ % pciconf -l
hostb0@pci0:0:0:0: class=0x060000 card=0xb30119da chip=0x22808086 rev=0x21 hdr=0x00
vgapci0@pci0:0:2:0: class=0x030000 card=0xb30119da chip=0x22b18086 rev=0x21 hdr=0x00
sdhci_pci0@pci0:0:16:0: class=0x080501 card=0xb30119da chip=0x22948086 rev=0x21 hdr=0x00
ahci0@pci0:0:19:0: class=0x010601 card=0xb30119da chip=0x22a38086 rev=0x21 hdr=0x00
xhci0@pci0:0:20:0: class=0x0c0330 card=0xb30119da chip=0x22b58086 rev=0x21 hdr=0x00
none0@pci0:0:26:0: class=0x108000 card=0xb30119da chip=0x22988086 rev=0x21 hdr=0x00
hdac0@pci0:0:27:0: class=0x040300 card=0xb30119da chip=0x22848086 rev=0x21 hdr=0x00
pcib1@pci0:0:28:0: class=0x060400 card=0xb30119da chip=0x22c88086 rev=0x21 hdr=0x01
pcib2@pci0:0:28:1: class=0x060400 card=0xb30119da chip=0x22ca8086 rev=0x21 hdr=0x01
pcib3@pci0:0:28:2: class=0x060400 card=0xb30119da chip=0x22cc8086 rev=0x21 hdr=0x01
pcib4@pci0:0:28:3: class=0x060400 card=0xb30119da chip=0x22ce8086 rev=0x21 hdr=0x01
isab0@pci0:0:31:0: class=0x060100 card=0xb30119da chip=0x229c8086 rev=0x21 hdr=0x00
none1@pci0:0:31:3: class=0x0c0500 card=0xb30119da chip=0x22928086 rev=0x21 hdr=0x00
re0@pci0:2:0:0: class=0x020000 card=0x012310ec chip=0x816810ec rev=0x0c hdr=0x00
re1@pci0:3:0:0: class=0x020000 card=0x012310ec chip=0x816810ec rev=0x0c hdr=0x00
none2@pci0:4:0:0: class=0x028000 card=0x80708086 chip=0x08b38086 rev=0x83 hdr=0x00
root@machine:/home/user # usbconfig
ugen0.1: <0x8086 XHCI root HUB> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA)
ugen0.2: <vendor 0x1a40 USB 2.0 Hub> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA)
ugen0.3: <Generic USB2.0-CRW> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (500mA)
ugen0.4: <vendor 0x8087 product 0x07dc> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA)
ugen0.5: <vendor 0x1a40 USB 2.0 Hub> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA)
ugen0.6: <vendor 0x04f3 product 0x0103> at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA)
ugen0.7: <SanDisk Extreme> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (200mA)
Thanks in advance