Fresh 10.0RC-3 install, generic kernel: I am having difficulty mounting USB drive file systems, and wondering if anyone can school me on how FUSE interacts with the kernel (as I under stand it is part of the base).
For a WD NTFS drive here is what I am getting:
No fuse module loaded, nor can I load it, and fusefs_enable="YES" had no effect in rc.conf:
When I mount the partition, it hesitates for a moment then:
Nor can I load it with
And just for kicks and giggles, I tried mounting an ext2 file system from my other USB device listed above (da1), I know in the past you had to build ext2 support into the file system, but I do not believe this to be true anymore?
/usr/src/UPDATING doesn't show ntfs as an unsupported fs type as it did before. And building fusefs-kmod returns:
FreeBSD has always been friendly mounting for me in the past, so I am not sure where to begin/continue my troubleshooting. Thanks in advance for any assistance.
Not sure if it is useful at all but:
For a WD NTFS drive here is what I am getting:
Code:
# camcontrol devlist
<OCZ-VERTEX4 1.5> at scbus2 target 0 lun 0 (ada0,pass0)
<WDC WD1002FAEX-00Z3A0 05.01D05> at scbus4 target 0 lun 0 (ada1,pass1)
<WDC WD1002FAEX-00Z3A0 05.01D05> at scbus5 target 0 lun 0 (ada2,pass2)
<WDC WD1002FAEX-00Z3A0 05.01D05> at scbus6 target 0 lun 0 (ada3,pass3)
<WDC WD1002FAEX-00Z3A0 05.01D05> at scbus7 target 0 lun 0 (ada4,pass4)
<WD My Passport 0740 1003> at scbus8 target 0 lun 0 (da0,pass5)
<WD SES Device 1003> at scbus8 target 0 lun 1 (pass6,ses0)
<SanDisk SDDR-113 1.00> at scbus9 target 0 lun 0 (da1,pass7)
Code:
# gpart show da0
=> 63 1953458113 da0 MBR (931G)
63 1985 - free - (993K)
2048 1953456128 1 ntfs (931G)
Code:
ls /dev/da*
/dev/da0 /dev/da0s1 /dev/da1 /dev/da1s1
No fuse module loaded, nor can I load it, and fusefs_enable="YES" had no effect in rc.conf:
Code:
# kldstat
Id Refs Address Size Name
1 17 0xffffffff80200000 15ef860 kernel
2 1 0xffffffff817f0000 23ab28 zfs.ko
3 2 0xffffffff81a2b000 6630 opensolaris.ko
4 1 0xffffffff81a32000 203d0 geom_eli.ko
5 3 0xffffffff81a53000 34e80 crypto.ko
6 1 0xffffffff81a89000 6d90 aesni.ko
When I mount the partition, it hesitates for a moment then:
Code:
# ntfs-3g /dev/da0s1 /mnt/usb
fuse: failed to open fuse device: No such file or directory
Nor can I load it with
mount
:
Code:
# mount -t ntfs /dev/da0s1 /mnt/usb
mount: /dev/da0s1: Operation not supported by device
And just for kicks and giggles, I tried mounting an ext2 file system from my other USB device listed above (da1), I know in the past you had to build ext2 support into the file system, but I do not believe this to be true anymore?
Code:
mount -t ext2fs /dev/da1s1 /mnt/usb
mount: /dev/da1s1: Operation not supported by device
/usr/src/UPDATING doesn't show ntfs as an unsupported fs type as it did before. And building fusefs-kmod returns:
Code:
/usr/ports/sysutils/fusefs-kmod # make install clean
===> fusefs-kmod-0.3.9.p1.20080208_11 Integrated into base.
*** Error code 1
FreeBSD has always been friendly mounting for me in the past, so I am not sure where to begin/continue my troubleshooting. Thanks in advance for any assistance.
Not sure if it is useful at all but:
Code:
#usbconfig
ugen4.1: <EHCI root HUB ATI> at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen3.1: <OHCI root HUB ATI> at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen2.1: <EHCI root HUB ATI> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen1.1: <OHCI root HUB ATI> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen0.1: <XHCI root HUB 0x1106> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA)
ugen7.1: <EHCI root HUB ATI> at usbus7, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen6.1: <OHCI root HUB ATI> at usbus6, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen5.1: <OHCI root HUB ATI> at usbus5, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen0.2: <USB2.0 Hub vendor 0x2109> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA)
ugen0.3: <USB Mouse vendor 0x05e3> at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (48mA)
ugen2.2: <SDDR-113 SanDisk Corp.> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (250mA)
ugen0.4: <My Passport 0740 Western Digital> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=ON (200mA)