Clone Intel 82576 PCIe x4 dual-port ethernet card doesn't exist

We purchased a clone Intel 82576 PCIe x4 dual-port 1000 Mbps ethernet card. We plugged it into the PCIe x16 slot of a Levono 510S-07IMB PC. However, ifconfig didn't show its two adapters (which should have been emXs).

Also,
Code:
pciconf -lv | grep -A 3 -I network
didn't find any devices related to Intel 82576. Interestingly, once the host was powered up, the green LED of both ports lit up while we plugged wire into them. The Levono host doesn't provide advanced BIOS configuration access to us.

Is this a hardware issue of the Intel 82576 (Dead on Arrival), or it just a compatible issue? How about Intel I350T2? Gemini suggested me those two cards and it was a mistake. 😰
 
If the device doesn't show up with pciconf(8) the actual hardware doesn't work. The tool queries ACPI directly.
 
chances are that lenovo has some sort of hardware whitelist so it will only work with lenovo (or 'certified') hardware.
Cross-check that card in another system, if it's dead just get it replaced.

I210, I350 etc will all work as well as pretty much all other intel chips - after all they are bog standard ancient 1Gbps, no rocket science involved... (or mellanox, chelsio etc although I'd stay away from cheap crap like e.g. realtek)
 
chances are that lenovo has some sort of hardware whitelist so it will only work with lenovo (or 'certified') hardware.
Good point. I wouldn't be surprised if they limited the PCIe x16 slot to graphics cards only,
 
Thanks for these tips, buddies. I asked Lenovo support about this host and they said there is no data about the whitelist mechanism. However, they didn't recommend me to try this behavior. I plan to try I350 later.
 
Apart from expecting non genuine hardware to work and I'd strongly suggest that you should avoid ~15 year old hardware that's since long end of life.
Be aware that you motherboard very likely doesn't support bifurcation so something like a dual port Intel i225*/226* card wont work unless there's PCI switch which itself can introduce other issues especially on cheap NICs.
 
I350 (PCIex4) has arrived but the same problem reproduced. No device under
Code:
pciconf -lv

I returned the NIC to exchange for a last try (I350 PCIex1). If it isn't woking, I quit.
 
I fear it might be limited, Lenovo is known to do shenanigans like that. I have several run-of-the-mill ATX/ITX mainboards where I stuck a PCIe x8 or x4 SAS/SATA controller in the x16 slot, never had an issue with that.
 
Finally, I purchased an intel 82576 PCIe x1 dual-port ethernet card and it works. The two ports are recognized as igb0 and igb1, respectively. Still a lot a word to do (transfer from my old FreeBSD to this new host). Thanks guys.

Sorry, I should have been 92575EB. I think they sent me a wrong item.
Code:
vendor     = 'Intel Corporation'
    device     = '82575EB Gigabit Network Connection'
    class      = network
    subclass   = ethernet
 
82575EB is not working. Static IP could be set and ifconfig shows active interface. But ping to other hosts just shows "host is down" message.
 
host is down means no arp reply. so you either can't send or can't receive. do you see your arp requests from another host ?
you may try play with media options and see if anything changes
 
Here. BTW, are this 82575EB PCIex1 native card? Or it is a native PCIex4, and just made into PCIex1 by small homebred mills.

I don't know. Maybe a native dual-port PCIex1 is the choice but now I would try intel I210 PCIex1, which gemini said is a native PCIex1 single-port NIC.

IMG_9612.jpeg
 
Back
Top