I am using the following setting
I included mps_load="YES" in loader.conf to use the card and rebooted.
mpsutil prints the following
It looks fine. But mps driver prints the following message endlessly, and the filesystem hangs during that reinitialization.
All disks are detected by kernel and zpool status looks fine.
I can access the file system in this zdata pool between each IOC fault error.
What do I need to do now?
Thanks.
- OS: FreeBSD-12.0-Release-p9
- 2 ports PCIe HBA attached with 2 SSDs
- ZFS mirrored. '/' directory exists and FreeBSD is installed here
- 6 Mainboard SATA ports
- ZFS RAIDZ2 with 6 HDD disks for private data. '/zdata' pool is here.
I included mps_load="YES" in loader.conf to use the card and rebooted.
mpsutil prints the following
Code:
[root@freebsd01~] mpsutil show all
Adapter:
mps0 Adapter:
Board Name: SAS9207-8i
Board Assembly: H5-25412-00C
Chip Name: LSISAS2308
Chip Revision: ALL
BIOS Revision: 7.39.02.00
Firmware Revision: 20.00.07.00
Integrated RAID: no
PhyNum CtlrHandle DevHandle Disabled Speed Min Max Device
0 0001 0009 N 6.0 1.5 6.0 SAS Initiator
1 0002 000a N 6.0 1.5 6.0 SAS Initiator
2 0003 000b N 6.0 1.5 6.0 SAS Initiator
3 0004 000c N 6.0 1.5 6.0 SAS Initiator
4 0005 000d N 6.0 1.5 6.0 SAS Initiator
5 0006 000e N 6.0 1.5 6.0 SAS Initiator
6 N 1.5 6.0 SAS Initiator
7 N 1.5 6.0 SAS Initiator
Devices:
B____T SAS Address Handle Parent Device Speed Enc Slot Wdt
00 03 4433221100000000 0009 0001 SATA Target 6.0 0001 03 1
00 02 4433221101000000 000a 0002 SATA Target 6.0 0001 02 1
00 01 4433221102000000 000b 0003 SATA Target 6.0 0001 01 1
00 00 4433221103000000 000c 0004 SATA Target 6.0 0001 00 1
00 05 4433221104000000 000d 0005 SATA Target 6.0 0001 07 1
00 04 4433221105000000 000e 0006 SATA Target 6.0 0001 06 1
Enclosures:
Slots Logical ID SEPHandle EncHandle Type
08 500605b005e9c9d0 0001 Direct Attached SGPIO
Expanders:
NumPhys SAS Address DevHandle Parent EncHandle SAS Level
It looks fine. But mps driver prints the following message endlessly, and the filesystem hangs during that reinitialization.
Code:
mps0: IOC Fault 0x4000265d, Resetting
mps0: Reinitializing controller
mps0: Firmware: 20.00.07.00, Driver: 21.02.00.00-fbsd
mps0: IOCCapabilities: 5a85c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,MSIXIndex,HostDisc>
All disks are detected by kernel and zpool status looks fine.
Code:
pool: zdata
state: ONLINE
scan: resilvered 0 in 0 days 00:00:11 with 0 errors on Sat Sep 7 13:53:11 2019
config:
NAME STATE READ WRITE CKSUM
zdata ONLINE 0 0 0
raidz2-0 ONLINE 0 0 0
da3 ONLINE 0 0 0
da2 ONLINE 0 0 0
da1 ONLINE 0 0 0
da0 ONLINE 0 0 0
da5 ONLINE 0 0 0
da4 ONLINE 0 0 0
errors: No known data errors
I can access the file system in this zdata pool between each IOC fault error.
What do I need to do now?
Thanks.