I have 6-7 y.o. machine:
Asus P4S333/c, latest bios 1008 beta, P4 2.4GHz (i686), DDR333 2.5GB, 2 IDE HDDs, FDD, Geforce3 Ti200 (128MB).
All usb features are enabled in bios.
This machine is just great. The only problem it doesn't have usb2.0 that's why I tried to use usb2.0 pci card (VIA83c572).
Unfortunately it doesn't work in usb2.0 mode, only usb1.1.
Search showed that only few people have the same problem (windows world). One advice was to buy such a card for exactly same board and success was reported. I cannot say so.
How to connect to usb2.0 shown below in dmesg?
Asus P4S333/c, latest bios 1008 beta, P4 2.4GHz (i686), DDR333 2.5GB, 2 IDE HDDs, FDD, Geforce3 Ti200 (128MB).
All usb features are enabled in bios.
This machine is just great. The only problem it doesn't have usb2.0 that's why I tried to use usb2.0 pci card (VIA83c572).
Unfortunately it doesn't work in usb2.0 mode, only usb1.1.
Search showed that only few people have the same problem (windows world). One advice was to buy such a card for exactly same board and success was reported. I cannot say so.
How to connect to usb2.0 shown below in dmesg?
Code:
$ dmesg -a
FreeBSD 8.0-BETA2 #6: Fri Aug 14 14:50:57 EDT 2009
usbus0: <SiS 5571 USB controller> on ohci0
ohci1: <SiS 5571 USB controller> mem 0xde000000-0xde000fff irq 23 at device 2.3 on pci0
ohci1: [ITHREAD]
usbus1: <SiS 5571 USB controller> on ohci1
uhci0: <VIA 83C572 USB controller> port 0xa400-0xa41f irq 17 at device 9.0 on pci0
uhci0: [ITHREAD]
usbus2: <VIA 83C572 USB controller> on uhci0
uhci1: <VIA 83C572 USB controller> port 0xa000-0xa01f irq 18 at device 9.1 on pci0
uhci1: [ITHREAD]
usbus3: <VIA 83C572 USB controller> on uhci1
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xdd000000-0xdd0000ff irq 19 at device 9.2 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 0.95
usbus4: <VIA VT6202 USB 2.0 controller> on ehci0
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ugen0.1: <SiS> at usbus0
uhub0: <SiS OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
uhub0: 3 ports with 3 removable, self powered
ugen1.1: <SiS> at usbus1
uhub1: <SiS OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
uhub1: 3 ports with 3 removable, self powered
ugen2.1: <VIA> at usbus2
uhub2: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
Root mount waiting for: usbus4 usbus3 usbus2
uhub2: 2 ports with 2 removable, self powered
ugen3.1: <VIA> at usbus3
uhub3: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
uhub3: 2 ports with 2 removable, self powered
ugen4.1: <VIA> at usbus4
uhub4: <VIA EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
Root mount waiting for: usbus4
uhub4: 4 ports with 4 removable, self powered
Root mount waiting for: usbus4
ugen2.2: <vendor 0x046d> at usbus2
ugen3.2: <USBest Technology> at usbus3
umass0: <USBest Technology USB Mass Storage Device, class 0/0, rev 2.00/1.00, addr 2> on usbus3
umass0: SCSI over Bulk-Only; quirks = 0x0000
umass0:0:0:-1: Attached to scbus0
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Ut163 USB2FlashStorage 0.00> Removable Direct Access SCSI-2 device
da0: 1.000MB/s transfers
da0: 1927MB (3948543 512 byte sectors: 255H 63S/T 245C)
GEOM: da0: partition 1 does not end on a track boundary.
$