Hi evrybody,
Well looking around in this forum, I haven't seen yet a problem like mine (except here perhaps ...) so I would like to introduce my case :
I have 1 FBSD7.2 configured to use dot1q, one switch 3750 configured in vlan or trunking and one FW pfsense (fbsd also ...) configured in trunk mode.
Those 3 equipements doesn't communicate !!
here are the conf :
Server :
SWITCH:
let's forget the PFS for now, who could tell me if I'm wrong in the conf ?
Also I can tell that The mac address-table of the switch does not show the FBSD !
I have also try to put the interface of switch in strict access mode, it doesn't work ....
Any idea ???????
PS : I can show additional commands like sh ip arp (empty), sh int fa1/0/15 switchport (wich show that the port of the FBSD is really configured in trunk)
Thanks, Thanks and Thanks
Well looking around in this forum, I haven't seen yet a problem like mine (except here perhaps ...) so I would like to introduce my case :
I have 1 FBSD7.2 configured to use dot1q, one switch 3750 configured in vlan or trunking and one FW pfsense (fbsd also ...) configured in trunk mode.
Those 3 equipements doesn't communicate !!
here are the conf :
Server :
Code:
em0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
ether 00:50:56:ad:20:f0
media: Ethernet autoselect (1000baseTX <full-duplex>)
status: [B]active[/B]
em1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
ether 00:50:56:ad:21:b5
inet [ADMin IP] netmask 0xffffff00 broadcast 10.100.201.255
media: Ethernet autoselect (1000baseTX <full-duplex>)
status: active
plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> metric 0 mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
vlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=3<RXCSUM,TXCSUM>
ether 00:50:56:ad:20:f0
inet 213.223.138.67 netmask 0xfffffff8 broadcast 213.223.138.71
media: Ethernet autoselect (1000baseTX <full-duplex>)
status: active
vlan: [B]1939[/B] parent interface: [B]em0[/B]
Code:
interface FastEthernet1/0/15
description TEST to SERVER FBSD 7.2 on VMWARE
switchport trunk encapsulation dot1q
switchport trunk native vlan 1939
switchport mode trunk
end
SWITCH-VMW-BAS(config-if)#do sh run int fa1/0/24
Building configuration...
Current configuration : 153 bytes
!
interface FastEthernet1/0/24
description To FW 1 - PFSENSE
switchport trunk encapsulation dot1q
switchport trunk native vlan 1939
switchport mode trunk
end
!
interface Vlan1939
ip address 213.223.138.70 255.255.255.240
end
Also I can tell that The mac address-table of the switch does not show the FBSD !
I have also try to put the interface of switch in strict access mode, it doesn't work ....
Any idea ???????
PS : I can show additional commands like sh ip arp (empty), sh int fa1/0/15 switchport (wich show that the port of the FBSD is really configured in trunk)
Thanks, Thanks and Thanks