As far as I'm aware, this is a really short list. As in 'none'.Any suggestions on brands, chipsets etc?
As far as I'm aware, this is a really short list. As in 'none'.
http://www.thinkwiki.org/wiki/Category:X61_Tablet
Not sure if anyone has ever installed FreeBSD on one of these though, but I'd give it a try if a got one.
pciconf -v
.hostb0@pci0:0:0:0: class=0x060000 card=0x00091414 chip=0x22808086 rev=0x20 hdr=0x00
vendor = 'Intel Corporation'
device = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series SoC Transaction Register'
class = bridge
subclass = HOST-PCI
vgapci0@pci0:0:2:0: class=0x030000 card=0x00091414 chip=0x22b08086 rev=0x20 hdr=0x00
vendor = 'Intel Corporation'
device = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Configuration Registers'
class = display
subclass = VGA
none0@pci0:0:3:0: class=0x048000 card=0x00091414 chip=0x22b88086 rev=0x20 hdr=0x00
vendor = 'Intel Corporation'
device = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Imaging Unit'
class = multimedia
none1@pci0:0:11:0: class=0x118000 card=0x00091414 chip=0x22dc8086 rev=0x20 hdr=0x00
vendor = 'Intel Corporation'
device = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Power Management Controller'
class = dasp
xhci0@pci0:0:20:0: class=0x0c0330 card=0x72708086 chip=0x22b58086 rev=0x20 hdr=0x00
vendor = 'Intel Corporation'
device = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series USB xHCI Controller'
class = serial bus
subclass = USB
none2@pci0:0:26:0: class=0x108000 card=0x72708086 chip=0x22988086 rev=0x20 hdr=0x00
vendor = 'Intel Corporation'
device = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Trusted Execution Engine'
class = encrypt/decrypt
pcib1@pci0:0:28:0: class=0x060400 card=0x72708086 chip=0x22c88086 rev=0x20 hdr=0x01
vendor = 'Intel Corporation'
device = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Express Port'
class = bridge
subclass = PCI-PCI
isab0@pci0:0:31:0: class=0x060100 card=0x72708086 chip=0x229c8086 rev=0x20 hdr=0x00
vendor = 'Intel Corporation'
device = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCU'
class = bridge
subclass = PCI-ISA
none3@pci0:1:0:0: class=0x020000 card=0x045e0002 chip=0x2b3811ab rev=0x00 hdr=0x00
vendor = 'Marvell Technology Group Ltd.'
device = '88W8897 [AVASTAR] 802.11ac Wireless'
class = network
subclass = ethernet
Can you share some details of this? Are you using the ig4 driver? HID over i2c device?Everything runs fine except that the stylus isn't working after sleep/resume,
For now, I solved this problem by adding kldunload ig4 in /etc/rc.suspend and all commands activating touchpad in /etc/rc.resume. With this hack, I have working touchpad after resume, which is very nice.