Hi,
I'm trying to get a HighPoint Rocket 620 card working to use as a port-multiplier card for a drive array over eSata. HighPoint shows compatibility with Freebsd for this model, however any time I try to access one or more disks in the array, the controller and drives will disappear/detach, and if I let it attempt to retry, eventually the system will panic. It's also worth mentioning that the same drive array is accessible and reads/writes without issue via my motherboard's onboard SATA controller (albeit, only one drive in the array shows up when connected this way, hence the need for a port multiplier).
I get the following errors within 10-15 seconds of attempting to create a zpool via:
The controller appears to be recognized properly until I attempt to use it:
The controller/drives as reported by dmesg:
As others have had success with some of the following options in /boot/loader.conf, I tried them, but with no success:
Does this seem like a driver/configuration issue, or am I looking at a DOA controller card? Any insight much appreciated.
I'm trying to get a HighPoint Rocket 620 card working to use as a port-multiplier card for a drive array over eSata. HighPoint shows compatibility with Freebsd for this model, however any time I try to access one or more disks in the array, the controller and drives will disappear/detach, and if I let it attempt to retry, eventually the system will panic. It's also worth mentioning that the same drive array is accessible and reads/writes without issue via my motherboard's onboard SATA controller (albeit, only one drive in the array shows up when connected this way, hence the need for a port multiplier).
I get the following errors within 10-15 seconds of attempting to create a zpool via:
Code:
# zpool create -m /mnt/storage storage ada1 ada2 ada3 ada4
Code:
ahcich1: Timeout on slot 19 port 0
ahcich1: is 00000000 cs 00080000 ss 00000000 rs 00080000 tfd 50 serr 00000000 cmd 00739317
(ada1:ahcich1:0:0:0): WRITE_DMA. ACB: ca 00 60 00 00 40 00 00 00 00 01 00
(ada1:ahcich1:0:0:0): CAM status: Command timeout
(ada1:ahcich1:0:0:0): Retrying command
ahcich1: Poll timeout on slot 19 port 15
ahcich1: is 00000000 cs 00080000 ss 00000000 rs 00080000 tfd 150 serr 00000000 cmd 00738017
(aprobe4:ahcich1:0:15:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe4:ahcich1:0:15:0): CAM status: Command timeout
(aprobe4:ahcich1:0:15:0): Error 5, Retries exhausted
pmp0 at ahcich1 bus 0 scbus3 target 15 lun 0
pmp0: <Port Multiplier 0325197b 000e> detached
ada1 at ahcich1 bus 0 scbus3 target 0 lun 0
ada1: <ST31000524AS 0958> s/n 6VP4K6VN detached
ada2 at ahcich1 bus 0 scbus3 target 1 lun 0
ada2: <SAMSUNG HD103UJ 1AA01118> s/n S13PJ90SC13402 detached
ada3 at ahcich1 bus 0 scbus3 target 2 lun 0
ada3: <SAMSUNG HD103UJ 1AA01118> s/n S13PJ90SC13405 detached
ada4 at ahcich1 bus 0 scbus3 target 3 lun 0
ada4: <ST31000528AS CC37> s/n 9VP2GEQ6 detached
ahcich1: Timeout on slot 19 port 0
ahcich1: is 00000000 cs 00f80000 ss 00000000 rs 00f80000 tfd 150 serr 00000000 cmd 00738017
ahcich1: ... waiting for slots 00f00000
ahcich1: Timeout on slot 20 port 1
ahcich1: is 00000000 cs 00f80000 ss 00000000 rs 00f80000 tfd 150 serr 00000000 cmd 00738017
ahcich1: ... waiting for slots 00e00000
ahcich1: Timeout on slot 21 port 2
ahcich1: is 00000000 cs 00f80000 ss 00000000 rs 00f80000 tfd 150 serr 00000000 cmd 00738017
ahcich1: ... waiting for slots 00c00000
ahcich1: Timeout on slot 22 port 3
ahcich1: is 00000000 cs 00f80000 ss 00000000 rs 00f80000 tfd 150 serr 00000000 cmd 00738017
ahcich1: ... waiting for slots 00800000
ahcich1: Timeout on slot 23 port 15
ahcich1: is 00000000 cs 00f80000 ss 00000000 rs 00f80000 tfd 150 serr 00000000 cmd 00738017
(aprobe0:ahcich1:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00
(aprobe0:ahcich1:0:0:0): CAM status: Command timeout
(aprobe0:ahcich1:0:0:0): Error 5, Retry was blocked
(aprobe1:ahcich1:0:1:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00
(aprobe1:ahcich1:0:1:0): CAM status: Command timeout
(aprobe1:ahcich1:0:1:0): Error 5, Retry was blocked
(aprobe2:ahcich1:0:2:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00
(aprobe2:ahcich1:0:2:0): CAM status: Command timeout
(aprobe2:ahcich1:0:2:0): Error 5, Retry was blocked
(aprobe3:ahcich1:0:3:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00
(aprobe3:ahcich1:0:3:0): CAM status: Command timeout
(aprobe3:ahcich1:0:3:0): Error 5, Retry was blocked
(pmp0:ahcich1:0:15:0): WRITE_PM. ACB: e8 60 00 00 00 0f 00 00 00 00 00 00
(pmp0:ahcich1:0:15:0): CAM status: Command timeout
(pmp0:ahcich1:0:15:0): Error 5, Periph was invalidated
(pmp0:ahcich1:0:15:0): Periph destroyed
ahcich1: Poll timeout on slot 23 port 0
ahcich1: is 00000000 cs 00800000 ss 00000000 rs 00800000 tfd 150 serr 00000000 cmd 00738017
ahcich1: Poll timeout on slot 23 port 1
ahcich1: is 00000000 cs 00800000 ss 00000000 rs 00800000 tfd 150 serr 00000000 cmd 00738017
(aprobe0:ahcich1:0:0:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe0:ahcich1:0:0:0): CAM status: Command timeout
(aprobe0:ahcich1:0:0:0): Error 5, Retries exhausted
ahcich1: Poll timeout on slot 23 port 2
ahcich1: is 00000000 cs 00800000 ss 00000000 rs 00800000 tfd 150 serr 00000000 cmd 00738017
(aprobe1:ahcich1:0:1:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe1:ahcich1:0:1:0): CAM status: Command timeout
(aprobe1:ahcich1:0:1:0): Error 5, Retries exhausted
ahcich1: Poll timeout on slot 23 port 3
ahcich1: is 00000000 cs 00800000 ss 00000000 rs 00800000 tfd 150 serr 00000000 cmd 00738017
(aprobe2:ahcich1:0:2:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe2:ahcich1:0:2:0): CAM status: Command timeout
(aprobe2:ahcich1:0:2:0): Error 5, Retries exhausted
ahcich1: Poll timeout on slot 23 port 15
ahcich1: is 00000000 cs 00800000 ss 00000000 rs 00800000 tfd 150 serr 00000000 cmd 00738017
(aprobe3:ahcich1:0:3:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe3:ahcich1:0:3:0): CAM status: Command timeout
(aprobe3:ahcich1:0:3:0): Error 5, Retries exhausted
(aprobe4:ahcich1:0:15:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe4:ahcich1:0:15:0): CAM status: Command timeout
(aprobe4:ahcich1:0:15:0): Error 5, Retries exhausted
ahcich1: Timeout on slot 23 port 0
ahcich1: is 00000000 cs 07800000 ss 00000000 rs 07800000 tfd 150 serr 00000000 cmd 00738017
ahcich1: ... waiting for slots 07000000
ahcich1: Timeout on slot 24 port 1
ahcich1: is 00000000 cs 07800000 ss 00000000 rs 07800000 tfd 150 serr 00000000 cmd 00738017
ahcich1: ... waiting for slots 06000000
ahcich1: Timeout on slot 25 port 2
ahcich1: is 00000000 cs 07800000 ss 00000000 rs 07800000 tfd 150 serr 00000000 cmd 00738017
ahcich1: ... waiting for slots 04000000
ahcich1: Timeout on slot 26 port 3
ahcich1: is 00000000 cs 07800000 ss 00000000 rs 07800000 tfd 150 serr 00000000 cmd 00738017
(ada1:ahcich1:0:0:0): WRITE_DMA. ACB: ca 00 60 00 00 40 00 00 00 00 01 00
(ada1:ahcich1:0:0:0): CAM status: Command timeout
(ada1:ahcich1:0:0:0): Error 5, Periph was invalidated
(ada2:ahcich1:0:1:0): SETFEATURES ENABLE RCACHE. ACB: ef aa 00 00 00 40 00 00 00 00 00 00
(ada2:ahcich1:0:1:0): CAM status: Command timeout
(ada2:ahcich1:0:1:0): Error 5, Periph was invalidated
(ada2:ahcich1:0:1:0): Periph destroyed
(ada3:ahcich1:0:2:0): SETFEATURES ENABLE RCACHE. ACB: ef aa 00 00 00 40 00 00 00 00 00 00
(ada3:ahcich1:0:2:0): CAM status: Command timeout
(ada3:ahcich1:0:2:0): Error 5, Periph was invalidated
(ada3:ahcich1:0:2:0): Periph destroyed
(ada4:ahcich1:0:3:0): SETFEATURES ENABLE RCACHE. ACB: ef aa 00 00 00 40 00 00 00 00 00 00
(ada4:ahcich1:0:3:0): CAM status: Command timeout
(ada4:ahcich1:0:3:0): Error 5, Periph was invalidated
(ada1:ahcich1:0:0:0): Periph destroyed
(ada4:ahcich1:0:3:0): Periph destroyed
ahcich1: Poll timeout on slot 26 port 0
ahcich1: is 00000000 cs 04000000 ss 00000000 rs 04000000 tfd 150 serr 00000000 cmd 00738017
ahcich1: Poll timeout on slot 26 port 1
ahcich1: is 00000000 cs 04000000 ss 00000000 rs 04000000 tfd 150 serr 00000000 cmd 00738017
(aprobe0:ahcich1:0:0:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe0:ahcich1:0:0:0): CAM status: Command timeout
(aprobe0:ahcich1:0:0:0): Error 5, Retries exhausted
ahcich1: Poll timeout on slot 26 port 2
ahcich1: is 00000000 cs 04000000 ss 00000000 rs 04000000 tfd 150 serr 00000000 cmd 00738017
(aprobe1:ahcich1:0:1:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe1:ahcich1:0:1:0): CAM status: Command timeout
(aprobe1:ahcich1:0:1:0): Error 5, Retries exhausted
ahcich1: Poll timeout on slot 26 port 3
ahcich1: is 00000000 cs 04000000 ss 00000000 rs 04000000 tfd 150 serr 00000000 cmd 00738017
(aprobe2:ahcich1:0:2:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe2:ahcich1:0:2:0): CAM status: Command timeout
(aprobe2:ahcich1:0:2:0): Error 5, Retries exhausted
(aprobe3:ahcich1:0:3:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
(aprobe3:ahcich1:0:3:0): CAM status: Command timeout
(aprobe3:ahcich1:0:3:0): Error 5, Retries exhausted
The controller appears to be recognized properly until I attempt to use it:
Code:
# pciconf -lvcb
Code:
ahci0@pci0:2:0:0: class=0x010601 card=0x91201b4b chip=0x91201b4b rev=0x12 hdr=0x00
vendor = 'Marvell Technology Group Ltd.'
device = '88SE9120 SATA 6Gb/s Controller'
class = mass storage
subclass = SATA
bar [10] = type I/O Port, range 32, base 0xe090, size 8, enabled
bar [14] = type I/O Port, range 32, base 0xe080, size 4, enabled
bar [18] = type I/O Port, range 32, base 0xe070, size 8, enabled
bar [1c] = type I/O Port, range 32, base 0xe060, size 4, enabled
bar [20] = type I/O Port, range 32, base 0xe050, size 16, enabled
bar [24] = type Memory, range 32, base 0xe0700000, size 2048, enabled
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[50] = MSI supports 1 message
cap 10[70] = PCI-Express 2 legacy endpoint max data 128(512) link x1(x1)
speed 2.5(5.0) ASPM disabled(L0s/L1)
ecap 0001[100] = AER 1 0 fatal 0 non-fatal 5 corrected
atapci1@pci0:2:0:1: class=0x01018f card=0x91a41b4b chip=0x91a41b4b rev=0x12 hdr=0x00
vendor = 'Marvell Technology Group Ltd.'
device = '88SE9128 IDE Controller'
class = mass storage
subclass = ATA
bar [10] = type I/O Port, range 32, base 0xe040, size 8, enabled
bar [14] = type I/O Port, range 32, base 0xe030, size 4, enabled
bar [18] = type I/O Port, range 32, base 0xe020, size 8, enabled
bar [1c] = type I/O Port, range 32, base 0xe010, size 4, enabled
bar [20] = type I/O Port, range 32, base 0xe000, size 16, enabled
bar [24] = type Memory, range 32, base 0xe0520000, size 16, disabled
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[50] = MSI supports 1 message
cap 10[70] = PCI-Express 2 legacy endpoint max data 128(512) link x1(x1)
speed 2.5(5.0) ASPM disabled(L0s/L1)
ecap 0001[100] = AER 1 0 fatal 0 non-fatal 5 corrected
The controller/drives as reported by dmesg:
Code:
# dmesg
Code:
pmp0 at ahcich1 bus 0 scbus3 target 15 lun 0
pmp0: <Port Multiplier 0325197b 000e> ATA-0 device
pmp0: 300.000MB/s transfers (SATA 2.x, NONE, PIO 8192bytes)
pmp0: 5 fan-out ports
ada1 at ahcich1 bus 0 scbus3 target 0 lun 0
ada1: <ST31000524AS 0958> ATA-7 SATA 2.x device
ada1: Serial Number 6VP4K6VN
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 512bytes)
ada1: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad10
ada2 at ahcich1 bus 0 scbus3 target 1 lun 0
ada2: <SAMSUNG HD103UJ 1AA01118> ATA-7 SATA 2.x device
ada2: Serial Number S13PJ90SC13402
ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada2: Previously was known as ad11
ada3 at ahcich1 bus 0 scbus3 target 2 lun 0
ada3: <SAMSUNG HD103UJ 1AA01118> ATA-7 SATA 2.x device
ada3: Serial Number S13PJ90SC13405
ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada3: Command Queueing enabled
ada3: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada4 at ahcich1 bus 0 scbus3 target 3 lun 0
ada4: <ST31000528AS CC37> ATA-8 SATA 2.x device
ada4: Serial Number 9VP2GEQ6
ada4: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada4: Command Queueing enabled
ada4: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
As others have had success with some of the following options in /boot/loader.conf, I tried them, but with no success:
Code:
hw.pci.enable_msix="0"
hw.pci.enable_msi="0"
hint.ahci.0.msi="0"
hw.hptrr.attach_generic=0
Does this seem like a driver/configuration issue, or am I looking at a DOA controller card? Any insight much appreciated.