Hi,
I have just installed FreeBSD 10 on a thinkpad T430.
During the installation, there is a "Network configure" screen that sees both my wired and wireless interfaces, however, for both of them DHCP fails. However, I'm pretty sure it is not DHCP's or network fault, as you'll see below.
I skip the step, finish the installation, then, after running
The
So neither cabled or wireless NICs seem to work. I have another laptop in the network (on which I tested the same cable, and I use the same wireless network), on which both cabled and wireless network are fine, and DHCP gives ip, so I'm pretty sure that the network or cable are not the problem.
Also
Is it possible that the drivers for the NICs are not supported ? Looking for the numbers "82579" and 6205", from the device names, here: https://www.freebsd.org/releases/10.0R/hardware.html
I don't seem to find them.
Although, the FreeBSD Intel drivers found here, for the cabled NIC: https://downloadcenter.intel.com/De...g=eng&OSVersion=FreeBSD*&DownloadType=Drivers seem to cover my 82579LM model.
However, running
Or you think it is not a driver issue ?
Any help would be really appreciated!
Thanks,
Stefan
I have just installed FreeBSD 10 on a thinkpad T430.
During the installation, there is a "Network configure" screen that sees both my wired and wireless interfaces, however, for both of them DHCP fails. However, I'm pretty sure it is not DHCP's or network fault, as you'll see below.
I skip the step, finish the installation, then, after running
ifconfig
, I get:
Code:
em0: flags=8c02<BROADCAST,OACTIVE,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=4219b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_MAGIC,VLAN_HWTSO>
ether 00:21:cc:c3:a7:15
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect
status: no carrier
iwn0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290
ether 8c:70:5a:92:04:44
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
status: no carrier
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
ue0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 02:15:e0:ec:01:00
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
The
pciconf -lv | grep -B3 network
gives me:
Code:
em0@pci0:0:25:0: class=0x020000 card=0x21f317aa chip=0x15028086 rev=0x04 hdr=0x00
vendor = 'Intel Corporation'
device = '82579LM Gigabit Network Connection'
class = network
--
iwn0@pci0:3:0:0: class=0x028000 card=0x13118086 chip=0x00858086 rev=0x34 hdr=0x00
vendor = 'Intel Corporation'
device = 'Centrino Advanced-N 6205 [Taylor Peak]'
class = network
So neither cabled or wireless NICs seem to work. I have another laptop in the network (on which I tested the same cable, and I use the same wireless network), on which both cabled and wireless network are fine, and DHCP gives ip, so I'm pretty sure that the network or cable are not the problem.
Also
cat dmesg | grep em0
:
Code:
em0: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0x6040-0x605f mem 0xf5200000-0xf521ffff,0xf523b000-0xf523bfff irq 20 at device 25.0 on pci0
em0: Using an MSI interrupt
em0: Ethernet address: 00:21:cc:c3:a7:15
ahciem0: <AHCI enclosure management bridge> on ahci0
ses0 at ahciem0 bus 0 scbus3 target 0 lun 0
umodem0: <H5321 gw Mobile Broadband Modem> on usbus0
umodem0: data interface 2, has CM over data, has break
Is it possible that the drivers for the NICs are not supported ? Looking for the numbers "82579" and 6205", from the device names, here: https://www.freebsd.org/releases/10.0R/hardware.html
I don't seem to find them.
Although, the FreeBSD Intel drivers found here, for the cabled NIC: https://downloadcenter.intel.com/De...g=eng&OSVersion=FreeBSD*&DownloadType=Drivers seem to cover my 82579LM model.
However, running
make
inside the downloaded driver, does not seem to work.Or you think it is not a driver issue ?
Any help would be really appreciated!
Thanks,
Stefan