Hi,
wlan-network-install version 11.0 like a charme, slowly learning FreeBSD, running xorg, i3, alpine, dillo; installed midori and seamonkey.
With dillo I had no networkproblems, but after installing midori and seamonkey it happened sometimes that the the connection broke and the root terminal showed:
Yesterday this happened after some links in the browser, after some minutes surfing, suddenly. In the past I could reboot directly into FreeBSD and wlan0 was up again, but now I find in the boot messages:
When I reboot after 2 or 3 minutes wlan0 is up again, but the direct reboot ends up in the error message. Therefore I made a direct reboot into Voidlinux and got the same error. Then I shutdown, booted into the PuppyLinux Slacko 5.7 LiveCD and had a wlan0 out of the box!
What is going on there ? Is there any connection with the freshly installed browsers or is the built-in zyd0 breaking down slowly or another network using the same channel as mine ?
I found Thread forums.freebsd.org/threads/36347 helpfull.
Here are some details:
This is the code when connected.
This is the code when unconnected:
boot/loader.conf
/etc/wpa_supplicant.conf
/etc/rc.conf
I just notice that another new network in the neighbourhood uses also channel 1.
Any idea ?
Thnxs.
p.s. during writing this message the network was on !
wlan-network-install version 11.0 like a charme, slowly learning FreeBSD, running xorg, i3, alpine, dillo; installed midori and seamonkey.
With dillo I had no networkproblems, but after installing midori and seamonkey it happened sometimes that the the connection broke and the root terminal showed:
Code:
zyd0: device timeout
Yesterday this happened after some links in the browser, after some minutes surfing, suddenly. In the past I could reboot directly into FreeBSD and wlan0 was up again, but now I find in the boot messages:
Code:
no carrier
When I reboot after 2 or 3 minutes wlan0 is up again, but the direct reboot ends up in the error message. Therefore I made a direct reboot into Voidlinux and got the same error. Then I shutdown, booted into the PuppyLinux Slacko 5.7 LiveCD and had a wlan0 out of the box!
What is going on there ? Is there any connection with the freshly installed browsers or is the built-in zyd0 breaking down slowly or another network using the same channel as mine ?
I found Thread forums.freebsd.org/threads/36347 helpfull.
Here are some details:
$ifconfig
Code:
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 00:60:b3:62:bb:fc
inet 192.168.2.102 netmask 0xffffff00 broadcast 192.168.2.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO,_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet OFDM/36Mbps mode 11g
status: associated
ssid beasty channel 1 (2412 Mhz 11g) bssid 8a:25:2c:b1:76:d3
regdomain ETSI country DE authmode WPA2/802.11i privacy ON
deftxkey UNDEF TKIP 4:128-bit txpower 30 bmiss 7 scanvalid 60 bgscan
bgscanitvl 300 bgscanidle 250 roam:rssi 7 roam:rate 5 protmode CTS
roaming MANUAL
groups: wlan
This is the code when connected.
This is the code when unconnected:
Code:
wlan0: .......
media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
status: no carrier
ssid "another wireless network in the neighbourhood"
boot/loader.conf
Code:
linux.ko="YES"
kern.maxfiles="25000"
/etc/wpa_supplicant.conf
Code:
ctrl_interface=/var/run/wpa_supplicant
eapol_version=2
ap_scan=1
network={
ssid="beasty"
psk="my_key"
priority=5
}
/etc/rc.conf
Code:
/etc/rc.conf
code:
hostname:"free.dom.org"
keymap="de"
wlans_zyd0="wlan0"
ifconfig_wlan0="WPA DHCP"
create_args_wlan0="country DE regdomain ETSI"
sshd_enable="YES"
moused_enable="YES"
#Set dumpdev to "AUTO" to enable crash dumps, "NO" to disable
dumpdev="AUTO"
$ifconfig wlan0 up scan
Code:
beasty 8a:25:2c:b1:76:d3 1 54M -75:-95 100 E APCHANREP APCHANREP HTCAP WPA RSN WME BSSLOAD
$netstat -rn
Code:
Routing tables
Internet:
Destination Gateway Flags Netif Expire
default 192.168.2.1 UGS wlan0
127.0.0.1 link#2 UH lo0
192.168.2.0/24 link#3 U wlan0
192.168.2.102 link#3 UHS lo0
Internet6:
Destination Gateway Flags Netif Expire
::96 ::01 UGRS lo0
::1 link#2 UH lo0
::ffff:0.0.0.0/96 ::1 UGRS lo0
fe80::/10 ::1 UGRS lo0
fe80::%lo0/64 link#2 U lo0
fe80::1%lo0 link#2 UHS lo0
ff02::/16 ::1 UGRS lo0
$wpa_supplicant -d -i wlan0 -c/etc/wpa_supplicant.conf
Code:
.......
wlan0: Authentication with 8a:25:2c:b1:76:d3 timed out.
Added BSSID 8a:25:2c:b1:76:d3 into blacklist.
.......
wlan0: * reason 3 (locally generated)
Any idea ?
Thnxs.
p.s. during writing this message the network was on !