Solved Xorg on Dell Latitude e6510

D

drobison

Hiya,

I'm running PCBSD 10.1 and am bringing this issue here because of the lack of response on the PCBSD forums.

My Dell Latitude E6510 uses the Intel agp0 Ironlake chip and as recently as PCBSD 10.0, it worked find when the laptop is docked and I'm using my external monitor (HDMI).

Now, however, I can only do this in VESA mode. When I boot with the Intel driver, the screen will go black, with a white cursor in the upper leftmost corner and my mouse pointer will freeze toward that corner. Works fine in either mode if I'm not docked.

I assume this is a problem with Xorg though perhaps it's the new vt(4). At any rate, I'm wondering where to start looking.

I booted normally, let it fail, then booted VESA and have an xorg.0.log.old.

I'll post it in a few messages... since it's too large.
 
Last edited:
Code: 
[ 77.230]
X.Org X Server 1.12.4
Release Date: 2012-08-27
[ 77.230] X Protocol Version 11, Revision 0
[ 77.230] Build Operating System: FreeBSD 10.0-RELEASE-p19 amd64
[ 77.230] Current Operating System: FreeBSD lefty 10.1-RELEASE-p8 FreeBSD 10.1-RELEASE-p8 #0: Thu Nov 13 13:17:05 UTC 2014 root@amd64-builder.pcbsd.org:/usr/obj/usr/src/sys/GENERIC amd64
[ 77.230] Build Date: 13 December 2014 06:57:57PM
[ 77.230]
[ 77.230] Current version of pixman: 0.32.4
[ 77.230] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 77.230] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 77.230] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Dec 19 13:40:50 2014
[ 77.329] (==) Using config file: "/etc/X11/xorg.conf"
[ 77.329] (==) Using system config directory "/usr/local/share/X11/xorg.conf.d"
[ 77.346] (==) ServerLayout "XFree86 Configured"
[ 77.346] (**) |-->Screen "Screen0" (0)
[ 77.346] (**) | |-->Monitor "<default monitor>"
[ 77.346] (**) | |-->Device "Card0"
[ 77.346] (==) No monitor specified for screen "Screen0".
Using a default monitor configuration.
[ 77.346] (**) |-->Input Device "Mouse0"
[ 77.347] (**) |-->Input Device "Keyboard0"
[ 77.347] (==) Automatically adding devices
[ 77.347] (==) Automatically enabling devices
[ 77.391] (WW) The directory "/usr/local/lib/X11/fonts/TrueType/" does not exist.
[ 77.391] Entry deleted from font path.
[ 77.391] (WW) The directory "/usr/local/lib/X11/fonts/illinoy/" does not exist.
[ 77.391] Entry deleted from font path.
[ 77.424] (WW) The directory "/usr/local/lib/X11/fonts/Speedo/" does not exist.
[ 77.424] Entry deleted from font path.
[ 77.453] (WW) The directory "/usr/local/lib/X11/fonts/CID/" does not exist.
[ 77.453] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/hebrew/" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/vietnamese/" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/indic/" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/fonts-indic/" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/ae_fonts1/AAHS" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/ae_fonts1/AGA" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/ae_fonts1/FS" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/ae_fonts1/Kasr" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/ae_fonts1/MCS" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.496] (WW) The directory "/usr/local/lib/X11/fonts/ae_fonts1/Shmookh" does not exist.
[ 77.496] Entry deleted from font path.
[ 77.508] (WW) `fonts.dir' not found (or not valid) in "/usr/local/lib/X11/fonts/local/".
[ 77.508] Entry deleted from font path.
[ 77.508] (Run 'mkfontdir' on "/usr/local/lib/X11/fonts/local/").
[ 77.521] (**) FontPath set to:
/usr/local/lib/X11/fonts/cyrillic/,
/usr/local/lib/X11/fonts/webfonts/,
/usr/local/lib/X11/fonts/misc/,
/usr/local/lib/X11/fonts/TTF/,
/usr/local/lib/X11/fonts/Type1/,
/usr/local/lib/X11/fonts/75dpi/,
/usr/local/lib/X11/fonts/100dpi/,
/usr/local/lib/X11/fonts/dejavu/,
/usr/local/lib/X11/fonts/cyrillic/,
/usr/local/lib/X11/fonts/misc/,
/usr/local/lib/X11/fonts/TTF/,
/usr/local/lib/X11/fonts/OTF/,
/usr/local/lib/X11/fonts/Type1/,
/usr/local/lib/X11/fonts/100dpi/,
/usr/local/lib/X11/fonts/75dpi/
[ 77.521] (**) ModulePath set to "/usr/local/lib/modules,/usr/local/lib/xorg/modules"
[ 77.521] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 77.521] (WW) Disabling Mouse0
[ 77.521] (WW) Disabling Keyboard0
[ 77.521] (II) Loader magic: 0x7b74f0
[ 77.521] (II) Module ABI versions:
[ 77.521] X.Org ANSI C Emulation: 0.4
[ 77.521] X.Org Video Driver: 12.1
[ 77.521] X.Org XInput driver : 16.0
[ 77.521] X.Org Server Extension : 6.0
[ 77.521] (--) PCI:*(0:0:2:0) 8086:0046:1028:040b rev 2, Mem @ 0xf0000000/4194304, 0xe0000000/268435456, I/O @ 0x00007110/8, BIOS @ 0x????????/65536
[ 77.521] (II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
[ 77.521] (II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
[ 77.521] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[ 77.521] (II) "record" will be loaded. This was enabled by default and also specified in the config file.
[ 77.521] (II) "dri" will be loaded. This was enabled by default and also specified in the config file.
[ 77.521] (II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
[ 77.522] (II) LoadModule: "extmod"
[ 77.582] (II) Loading /usr/local/lib/xorg/modules/extensions/libextmod.so
[ 77.584] (II) Module extmod: vendor="X.Org Foundation"
[ 77.584] compiled for 1.12.4, module version = 1.0.0
[ 77.584] Module class: X.Org Server Extension
[ 77.584] ABI class: X.Org Server Extension, version 6.0
[ 77.584] (II) Loading extension MIT-SCREEN-SAVER
[ 77.584] (II) Loading extension XFree86-VidModeExtension
[ 77.584] (II) Loading extension XFree86-DGA
[ 77.584] (II) Loading extension DPMS
[ 77.584] (II) Loading extension XVideo
[ 77.584] (II) Loading extension XVideo-MotionCompensation
[ 77.584] (II) Loading extension X-Resource
[ 77.584] (II) LoadModule: "record"
[ 77.584] (II) Loading /usr/local/lib/xorg/modules/extensions/librecord.so
 
Code: 
[ 77.585] (II) Module record: vendor="X.Org Foundation"
[ 77.585] compiled for 1.12.4, module version = 1.13.0
[ 77.585] Module class: X.Org Server Extension
[ 77.585] ABI class: X.Org Server Extension, version 6.0
[ 77.585] (II) Loading extension RECORD
[ 77.585] (II) LoadModule: "dbe"
[ 77.586] (II) Loading /usr/local/lib/xorg/modules/extensions/libdbe.so
[ 77.586] (II) Module dbe: vendor="X.Org Foundation"
[ 77.586] compiled for 1.12.4, module version = 1.0.0
[ 77.586] Module class: X.Org Server Extension
[ 77.586] ABI class: X.Org Server Extension, version 6.0
[ 77.586] (II) Loading extension DOUBLE-BUFFER
[ 77.586] (II) LoadModule: "glx"
[ 77.587] (II) Loading /usr/local/lib/xorg/modules/extensions/libglx.so
[ 77.591] (II) Module glx: vendor="X.Org Foundation"
[ 77.591] compiled for 1.12.4, module version = 1.0.0
[ 77.592] ABI class: X.Org Server Extension, version 6.0
[ 77.593] (==) AIGLX enabled
[ 77.593] (II) Loading extension GLX
[ 77.593] (II) LoadModule: "dri"
[ 77.593] (II) Loading /usr/local/lib/xorg/modules/extensions/libdri.so
[ 77.620] (II) Module dri: vendor="X.Org Foundation"
[ 77.620] compiled for 1.12.4, module version = 1.0.0
[ 77.620] ABI class: X.Org Server Extension, version 6.0
[ 77.620] (II) Loading extension XFree86-DRI
[ 77.620] (II) LoadModule: "dri2"
[ 77.621] (II) Loading /usr/local/lib/xorg/modules/extensions/libdri2.so
[ 77.621] (II) Module dri2: vendor="X.Org Foundation"
[ 77.621] compiled for 1.12.4, module version = 1.2.0
[ 77.621] ABI class: X.Org Server Extension, version 6.0
[ 77.621] (II) Loading extension DRI2
[ 77.621] (II) LoadModule: "intel"
[ 77.659] (II) Loading /usr/local/lib/xorg/modules/drivers/intel_drv.so
[ 77.704] (II) Module intel: vendor="X.Org Foundation"
[ 77.704] compiled for 1.12.4, module version = 2.21.15
[ 77.704] Module class: X.Org Video Driver
[ 77.704] ABI class: X.Org Video Driver, version 12.1
[ 77.704] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, HD Graphics,
HD Graphics 2000, HD Graphics 3000, HD Graphics 2500,
HD Graphics 4000, HD Graphics P4000, HD Graphics 4600,
HD Graphics 5000, HD Graphics P4600/P4700, Iris(TM) Graphics 5100,
HD Graphics 4400, HD Graphics 4200, Iris(TM) Pro Graphics 5200
[ 77.705] (--) Using syscons driver with X support (version 2.0)
[ 77.705] (--) using VT number 9

[ 79.886] drmOpenDevice: node name is /dev/dri/card0
[ 79.886] drmOpenDevice: open result is 8, (OK)
[ 79.886] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 79.886] drmOpenDevice: node name is /dev/dri/card0
[ 79.886] drmOpenDevice: open result is 8, (OK)
[ 79.886] drmOpenByBusid: drmOpenMinor returns 8
[ 79.886] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 81.378] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[ 81.378] drmOpenDevice: node name is /dev/dri/card0
[ 81.378] drmOpenDevice: open result is 8, (OK)
[ 81.378] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 81.378] drmOpenDevice: node name is /dev/dri/card0
[ 81.378] drmOpenDevice: open result is 8, (OK)
[ 81.378] drmOpenByBusid: drmOpenMinor returns 8
[ 81.378] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 81.378] (II) intel(0): Creating default Display subsection in Screen section
"Screen0" for depth/fbbpp 24/32
[ 81.378] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 81.378] (==) intel(0): RGB weight 888
[ 81.378] (==) intel(0): Default visual is TrueColor
[ 81.378] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics
[ 81.378] (**) intel(0): Relaxed fencing enabled
[ 81.378] (**) intel(0): Wait on SwapBuffers? enabled
[ 81.378] (**) intel(0): Triple buffering? enabled
[ 81.378] (**) intel(0): Framebuffer tiled
[ 81.378] (**) intel(0): Pixmaps tiled
[ 81.378] (**) intel(0): 3D buffers tiled
[ 81.378] (**) intel(0): SwapBuffers wait enabled
[ 81.378] (==) intel(0): video overlay key set to 0x101fe
[ 81.434] (II) intel(0): Output eDP1 has no monitor section
[ 81.435] (II) intel(0): Output VGA1 has no monitor section
[ 81.443] (II) intel(0): Output HDMI1 has no monitor section
[ 81.461] (II) intel(0): Output DP1 has no monitor section
[ 81.499] (II) intel(0): Output HDMI2 has no monitor section
[ 81.508] (II) intel(0): Output HDMI3 has no monitor section
[ 81.526] (II) intel(0): Output DP2 has no monitor section
[ 81.544] (II) intel(0): Output DP3 has no monitor section
[ 81.600] (II) intel(0): EDID for output eDP1
[ 81.600] (II) intel(0): Manufacturer: SEC Model: 544b Serial#: 0
[ 81.600] (II) intel(0): Year: 2010 Week: 0
[ 81.600] (II) intel(0): EDID Version: 1.0
[ 81.600] (II) intel(0): Digital Display Input
[ 81.600] (II) intel(0): Max Image Size [cm]: horiz.: 34 vert.: 19
[ 81.600] (II) intel(0): Gamma: 2.20
[ 81.600] (II) intel(0): No DPMS capabilities specified
[ 81.600] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 81.600] (II) intel(0): First detailed timing is preferred mode
[ 81.600] (II) intel(0): redX: 0.620 redY: 0.340 greenX: 0.330 greenY: 0.570
[ 81.600] (II) intel(0): blueX: 0.150 blueY: 0.060 whiteX: 0.313 whiteY: 0.329
[ 81.600] (II) intel(0): Manufacturer's mask: 0
[ 81.600] (II) intel(0): Supported detailed timing:
[ 81.600] (II) intel(0): clock: 107.8 MHz Image Size: 344 x 194 mm
[ 81.600] (II) intel(0): h_active: 1600 h_sync: 1648 h_sync_end 1680 h_blank_end 1932 h_border: 0
[ 81.600] (II) intel(0): v_active: 900 v_sync: 902 v_sync_end 907 v_blanking: 930 v_border: 0
[ 81.600] (II) intel(0): Supported detailed timing:
[ 81.600] (II) intel(0): clock: 71.9 MHz Image Size: 344 x 194 mm
[ 81.601] (II) intel(0): h_active: 1600 h_sync: 1648 h_sync_end 1680 h_blank_end 1932 h_border: 0
[ 81.601] (II) intel(0): v_active: 900 v_sync: 902 v_sync_end 907 v_blanking: 930 v_border: 0
[ 81.601] (II) intel(0): EDID (in hex):
[ 81.601] (II) intel(0): 00ffffffffffff004ca34b5400000000
[ 81.601] (II) intel(0): 00140100952213780ac8959e57549226
[ 81.601] (II) intel(0): 0f505400000001010101010101010101
[ 81.601] (II) intel(0): 0101010101011c2a404c61841e303020
[ 81.601] (II) intel(0): 250058c21000001a131c404c61841e30
[ 81.601] (II) intel(0): 3020250058c21000001a000000fe0046
[ 81.601] (II) intel(0): 48353030803135364b540a2000000000
[ 81.601] (II) intel(0): 000041011e0000000009010a202000d7
[ 81.601] (II) intel(0): EDID vendor "SEC", prod id 21579
[ 81.601] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x838 mode
[ 81.601] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x0 mode
[ 81.601] (II) intel(0): Printing DDC gathered Modelines:
[ 81.601] (II) intel(0): Modeline "1600x900"x0.0 107.80 1600 1648 1680 1932 900 902 907 930 +hsync -vsync (55.8 kHz eP)
[ 81.601] (II) intel(0): Modeline "1600x900"x0.0 71.87 1600 1648 1680 1932 900 902 907 930 +hsync -vsync (37.2 kHz e)
[ 81.601] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 81.601] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 81.601] (II) intel(0): Printing probed modes for output eDP1
[ 81.601] (II) intel(0): Modeline "1600x900"x60.0 107.80 1600 1648 1680 1932 900 902 907 930 +hsync -vsync (55.8 kHz eP)
[ 81.601] (II) intel(0): Modeline "1600x900"x40.0 71.87 1600 1648 1680 1932 900 902 907 930 +hsync -vsync (37.2 kHz e)
[ 81.601] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d)
[ 81.601] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 81.601] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d)
[ 81.601] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 81.601] (II) intel(0): EDID for output VGA1
[ 81.610] (II) intel(0): EDID for output HDMI1
[ 81.628] (II) intel(0): EDID for output DP1
 
Code: 
[ 81.666] (II) intel(0): EDID for output HDMI2
[ 81.666] (II) intel(0): Manufacturer: DEL Model: a030 Serial#: 842018899
[ 81.666] (II) intel(0): Year: 2010 Week: 2
[ 81.666] (II) intel(0): EDID Version: 1.3
[ 81.666] (II) intel(0): Digital Display Input
[ 81.666] (II) intel(0): Max Image Size [cm]: horiz.: 58 vert.: 36
[ 81.666] (II) intel(0): Gamma: 2.20
[ 81.666] (II) intel(0): DPMS capabilities: StandBy Suspend Off
[ 81.666] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 81.666] (II) intel(0): First detailed timing is preferred mode
[ 81.666] (II) intel(0): redX: 0.675 redY: 0.318 greenX: 0.189 greenY: 0.704
[ 81.666] (II) intel(0): blueX: 0.147 blueY: 0.069 whiteX: 0.313 whiteY: 0.329
[ 81.666] (II) intel(0): Supported established timings:
[ 81.666] (II) intel(0): 720x400@70Hz
[ 81.666] (II) intel(0): 640x480@60Hz
[ 81.667] (II) intel(0): 640x480@75Hz
[ 81.667] (II) intel(0): 800x600@60Hz
[ 81.667] (II) intel(0): 800x600@75Hz
[ 81.667] (II) intel(0): 1024x768@60Hz
[ 81.667] (II) intel(0): 1024x768@75Hz
[ 81.667] (II) intel(0): 1280x1024@75Hz
[ 81.667] (II) intel(0): Manufacturer's mask: 0
[ 81.667] (II) intel(0): Supported standard timings:
[ 81.667] (II) intel(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 81.667] (II) intel(0): #1: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 81.667] (II) intel(0): #2: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 81.667] (II) intel(0): #3: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 81.667] (II) intel(0): Supported detailed timing:
[ 81.667] (II) intel(0): clock: 154.0 MHz Image Size: 582 x 364 mm
[ 81.667] (II) intel(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0
[ 81.667] (II) intel(0): v_active: 1200 v_sync: 1203 v_sync_end 1209 v_blanking: 1235 v_border: 0
[ 81.667] (II) intel(0): Serial No: HW117017200S
[ 81.667] (II) intel(0): Monitor name: DELL 2709W
[ 81.667] (II) intel(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 81.667] (II) intel(0): EDID (in hex):
[ 81.667] (II) intel(0): 00ffffffffffff0010ac30a053303032
[ 81.667] (II) intel(0): 02140103803a2478eae9f5ac5130b425
[ 81.667] (II) intel(0): 115054a54b008180a940714fb3000101
[ 81.667] (II) intel(0): 010101010101283c80a070b023403020
[ 81.667] (II) intel(0): 3600466c2100001a000000ff00485731
[ 81.667] (II) intel(0): 3137303137323030530a000000fc0044
[ 81.667] (II) intel(0): 454c4c2032373039570a2020000000fd
[ 81.667] (II) intel(0): 00384c1e5311000a2020202020200098
[ 81.667] (II) intel(0): Printing probed modes for output HDMI2
[ 81.667] (II) intel(0): Modeline "1920x1200"x60.0 154.00 1920 1968 2000 2080 1200 1203 1209 1235 +hsync -vsync (74.0 kHz eP)
[ 81.667] (II) intel(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 81.667] (II) intel(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[ 81.667] (II) intel(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 81.667] (II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 81.667] (II) intel(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 81.667] (II) intel(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 81.667] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 81.667] (II) intel(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 81.667] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 81.667] (II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 81.667] (II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 81.667] (II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 81.676] (II) intel(0): EDID for output HDMI3
[ 81.694] (II) intel(0): EDID for output DP2
[ 81.712] (II) intel(0): EDID for output DP3
[ 81.712] (II) intel(0): Output eDP1 connected
[ 81.712] (II) intel(0): Output VGA1 disconnected
[ 81.712] (II) intel(0): Output HDMI1 disconnected
[ 81.712] (II) intel(0): Output DP1 disconnected
[ 81.712] (II) intel(0): Output HDMI2 connected
[ 81.712] (II) intel(0): Output HDMI3 disconnected
[ 81.712] (II) intel(0): Output DP2 disconnected
[ 81.712] (II) intel(0): Output DP3 disconnected
[ 81.712] (II) intel(0): Using fuzzy aspect match for initial modes
[ 81.712] (II) intel(0): Output eDP1 using initial mode 1024x768
[ 81.712] (II) intel(0): Output HDMI2 using initial mode 1024x768
[ 81.712] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 81.712] (II) intel(0): Kernel page flipping support detected, enabling
[ 81.712] (**) intel(0): Display dimensions: (340, 190) mm
[ 81.712] (**) intel(0): DPI set to (76, 102)
[ 81.712] (II) Loading sub module "fb"
[ 81.712] (II) LoadModule: "fb"
[ 81.713] (II) Loading /usr/local/lib/xorg/modules/libfb.so
[ 81.732] (II) Module fb: vendor="X.Org Foundation"
[ 81.732] compiled for 1.12.4, module version = 1.0.0
[ 81.732] ABI class: X.Org ANSI C Emulation, version 0.4
[ 81.732] (II) Loading sub module "dri2"
[ 81.732] (II) LoadModule: "dri2"
[ 81.732] (II) Loading /usr/local/lib/xorg/modules/extensions/libdri2.so
[ 81.732] (II) Module dri2: vendor="X.Org Foundation"
[ 81.732] compiled for 1.12.4, module version = 1.2.0
[ 81.732] ABI class: X.Org Server Extension, version 6.0
[ 81.732] (==) Depth 24 pixmap format is 32 bpp
[ 81.732] (II) intel(0): [DRI2] Setup complete
[ 81.732] (II) intel(0): [DRI2] DRI driver: i965
[ 81.732] (II) intel(0): Allocated new frame buffer 1024x768 stride 4096, tiled
[ 81.739] (II) UXA(0): Driver registered support for the following operations:
[ 81.739] (II) solid
[ 81.739] (II) copy
[ 81.739] (II) composite (RENDER acceleration)
[ 81.739] (II) put_image
[ 81.739] (II) get_image
[ 81.739] (==) intel(0): Backing store disabled
[ 81.739] (==) intel(0): Silken mouse enabled
[ 81.739] (II) intel(0): Initializing HW Cursor
[ 81.739] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 81.739] (==) intel(0): DPMS enabled
[ 81.739] (==) intel(0): Intel XvMC decoder enabled
[ 81.739] (II) intel(0): Set up textured video
[ 81.739] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 81.740] (II) intel(0): direct rendering: DRI2 Enabled
 
OK I notice my post got moved here where nobody will ever see it.

Anyone have any suggestions where I can take this to get some exposure? Does it belong on freebsd-mobile or some other mail list? I don't want to post it to the wrong place.
 
Solved! Sort of.

I subscribed and posted this to the freebsd-mobile mail list. I received an email from a non-list subscriber who uses the same laptop and docking station.

At his suggestion I disabled the new VT in /boot/loader.conf.pcbsd, then remade grub with:

grub-mkconfig -o /boot/grub/grub.cfg

Rebooted and ran the PCBSD Display Manager and I am back up on the intel driver at 1900x1200.

Why the new VT and the intel driver do not play nicely together is a mystery to me.

I believe any FreeBSD user could simply disable the new VT in /boot/loader.conf to accomplish the same thing. The option is:

Code: 
kern.vty=vt

PCBSD has the grub loader and required the additional steps.
 
Actually wblock@, the OP mentioned that they'd first asked in the PCBSD fora and were posting here because of lack of response. To drobison, I would guess that most people browse by new post, so even if it's moved to a different section, it will probably get the same amount of views.

All that being said, I've found that the
Code: 
kern.vty=vt
to be necessary with my laptop, which has an Intel driver in order to enable me to use ctl+alt+Fx (or maybe just alt+Fx) to get to console or to exit X.

I've only found this necessary with Intel cards. On my workstation, which uses NVidia, there are no issues.
 
You must log in or register to reply here.
Back
Top