Upgrade 12.0 -> 12.1: USB not working

R

Reaperzx

After doing binary upgrade to 12.1 my USB seems to have stopped working:

Code: 
uhub_reattach_port: could not allocate new device
usb_alloc_device: set address 3 failed (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
ugen1.3: <Unknown > at usbus1 (disconnected)
uhub_reattach_port: could not allocate new device
usb_alloc_device: set address 3 failed (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
ugen1.3: <Unknown > at usbus1 (disconnected)
uhub_reattach_port: could not allocate new device
usb_alloc_device: set address 3 failed (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED

Log is full of that stuff, new lines every minute.

I have tried restarting and plugging to different USB port, no effect.

The mainboard is MSI B75MAP45 (s1155) + Core i5-3570 CPU. So B75 Chipset.

I have upgrade other machine, where is Z77 chipset, no problems there.
 
Try a different port, try a different medium, what messages do you get from that? I seen a few hits on this error form 2008 and 2014 and such.

usb_alloc_device: set address 2 failed

Hello - When I go into FreeNAS, I find pages of error code. I tried re-installing onto a new memory stick but still the error messages persist. I'm very new to this so I apologise up front if I've not provided enough information. Build is FreeNAS-11.1-U5 Motherboard: Dell Inc. ODR845 (CPU) CPU...
www.ixsystems.com

No USB after NAS4Free boot - XigmaNAS

www.xigmanas.com www.xigmanas.com
 
After updating to 12.1-RELEASE-p2 USB started working again!

So something WAS wrong and it has now been fixed!
 
You must log in or register to reply here.
Back
Top