(Solved) FreeBSD memstick not running

yo9fah

yo9fah

Hi! :)

I used to install FreeBSD v.9 method dd(1) on the stick and boot, but stops somewhere at one point and freezes there.

I installed FreeBSD v.8.3 and works very well, no problems.

I have an Acer Extensa 5220

LE: Solved in version FreeBSD-9.1-RC2
 
Hi, thanks for the reply. Everything goes well up here:

Code: 
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
<- At this point it stops and does not respond to any command!

Thanks in advance for help!
 
Try booting with ACPI turned off. See if that helps.

Also make sure the BIOS of the machine is up to date.
 
I tried with ACPI Turned off, but not work. The BIOS of the machine is up to date. I have the latest version. I tried to [cmd=]dd if=/dev/zero of=/dev/sdb bs=128M[/cmd] and then [cmd=]dd if=FreeBSD-9.0-RELEASE-amd64-memstick.img of=/dev/sdb bs=10240 conv=sync[/cmd] But had no effect.

I can not understand why running version 8.3 and version 9 does not work? How can I solve this problem?

Thanks again for help!
 
I've heard some issues with some laptops. Have a look and see if you can change setting regarding SATA. Some must be set to AHCI, some to Legacy, try anything but RAID.
 
SirDice said:
I've heard some issues with some laptops. Have a look and see if you can change setting regarding SATA. Some must be set to AHCI, some to Legacy, try anything but RAID.
Click to expand...

I tried but it does not work. Another idea? Thanks!
 
So, I want to install FreeBSD, version 8.3 works on my laptop. How can I upgrade to version 9 immediately after you install 8.3?

Thanks in advance!
 
I installed FreeBSD 9.0 i386 but you, ACPI = off (amd64, do not work on my laptop), works very well i386, but I have a boot problem, "Root mount waiting for: usbus2".

This is the output from dmesg:

Code: 
$ dmesg
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-RELEASE-p3 #0: Tue Jun 12 01:47:53 UTC 2012
    root@i386-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC i386
CPU: Intel(R) Celeron(R) CPU          560  @ 2.13GHz (2128.04-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x10661  Family = 6  Model = 16  Stepping = 1
  Features=0xafebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
  Features2=0xe31d<SSE3,DTES64,MON,DS_CPL,TM2,SSSE3,CX16,xTPR,PDCM>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant, performance statistics
real memory  = 2147483648 (2048 MB)
avail memory = 2077052928 (1980 MB)
MPTable: <INTEL    S. Rosa CRB >
Event timer "LAPIC" quality 400
ioapic0: Assuming intbase of 0
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem 0xfc000000-0xfc0fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
agp0: <Intel GM965 SVGA controller> on vgapci0
agp0: aperture size is 256M, detected 7676k stolen memory
vgapci1: <VGA-compatible display> mem 0xfc100000-0xfc1fffff at device 2.1 on pci0
uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0x1820-0x183f irq 20 at device 26.0 on pci0
uhci0: LegSup = 0x2020
usbus0: <Intel 82801H (ICH8) USB controller USB-D> on uhci0
uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0x1840-0x185f irq 21 at device 26.1 on pci0
usbus1: <Intel 82801H (ICH8) USB controller USB-E> on uhci1
ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem 0xfc504000-0xfc5043ff irq 20 at device 26.7 on pci0
usbus2: EHCI version 1.0
usbus2: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> on ehci0
hdac0: <Intel 82801H High Definition Audio Controller> mem 0xfc300000-0xfc303fff irq 21 at device 27.0 on pci0
pcib1: <MPTable PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <PCI bus> on pcib1
bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0x00b002> mem 0xf6000000-0xf600ffff irq 16 at device 0.0 on pci2
bge0: CHIP ID 0x0000b002; ASIC REV 0x0b; CHIP REV 0xb0; PCI-E
miibus0: <MII bus> on bge0
brgphy0: <BCM5754/5787 1000BASE-T media interface> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Ethernet address: 00:1d:72:32:45:5d
pcib2: <MPTable PCI-PCI bridge> irq 17 at device 28.1 on pci0
pci4: <PCI bus> on pcib2
pci4: <network> at device 0.0 (no driver attached)
pcib3: <PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci6: <PCI bus> on pcib3
uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0x1860-0x187f irq 23 at device 29.0 on pci0
usbus3: <Intel 82801H (ICH8) USB controller USB-A> on uhci2
uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0x1880-0x189f irq 17 at device 29.1 on pci0
usbus4: <Intel 82801H (ICH8) USB controller USB-B> on uhci3
uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0x18a0-0x18bf irq 18 at device 29.2 on pci0
usbus5: <Intel 82801H (ICH8) USB controller USB-C> on uhci4
ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem 0xfc504400-0xfc5047ff irq 23 at device 29.7 on pci0
usbus6: waiting for BIOS to give up control
usbus6: timed out waiting for BIOS
usbus6: EHCI version 1.0
usbus6: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> on ehci1
pcib4: <MPTable PCI-PCI bridge> at device 30.0 on pci0
pci15: <PCI bus> on pcib4
cbb0: <PCI-CardBus Bridge> mem 0xfc204000-0xfc204fff irq 22 at device 6.0 on pci15
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem 0xfc206000-0xfc2067ff,0xfc200000-0xfc203fff irq 22 at device 6.1 on pci15
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:1d:72:ff:ff:32:45:5d
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x14bc000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:1d:72:32:45:5d
fwe0: Ethernet address: 02:1d:72:32:45:5d
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:1d:72:ff:ff:32:45:5d @ 0xfffe00000000, S400, maxrec 2048
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
pci15: <mass storage> at device 6.2 (no driver attached)
pci15: <base peripheral, SD host controller> at device 6.3 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH8M UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1810-0x181f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
atapci1: <Intel ICH8M SATA300 controller> port 0x1c00-0x1c07,0x18f4-0x18f7,0x18f8-0x18ff,0x18f0-0x18f3,0x18e0-0x18ef,0x18d0-0x18df irq 19 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
cpu0 on motherboard
p4tcc0: <CPU Frequency Thermal Control> on cpu0
pmtimer0 on isa0
unknown: <PNP0c01> can't assign resources (memory)
attimer0: <AT timer> at port 0x40-0x43 irq 0 pnpid PNP0100 on isa0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
Event timer "RTC" frequency 32768 Hz quality 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 irq 1 pnpid PNP0303 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <INT0800> can't assign resources (memory)
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
orm0: <ISA Option ROMs> at iomem 0xcf000-0xcffff,0xe0000-0xe17ff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: parallel port not found.
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <INT0800> can't assign resources (memory)
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0)  (me) 
firewire0: bus manager 0 
hdac0: HDA Codec #0: Realtek ALC268
hdac0: HDA Codec #1: Conexant (Unknown)
pcm0: <HDA Realtek ALC268 PCM #0 Analog> at cad 0 nid 1 on hdac0
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
[B]ugen2.1: <Intel> at usbus2
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2[/B]
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
ada0 at ata2 bus 0 scbus1 target 0 lun 0
ada0: <TOSHIBA MK1646GSX LB113J> ATA-8 SATA 1.x device
ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada0: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
Timecounter "TSC" frequency 2128043840 Hz quality 1000
uhub2: 4 ports with 4 removable, self powered
Root mount waiting for: usbus6 usbus2
uhub6: 6 ports with 6 removable, self powered
[B]Root mount waiting for: usbus2
usb_alloc_device: set address 2 failed (USB_ERR_TIMEOUT, ignored)
Root mount waiting for: usbus2[/B]
Root mount waiting for: usbus2
Root mount waiting for: usbus2
Root mount waiting for: usbus2
Root mount waiting for: usbus2
Root mount waiting for: usbus2
Root mount waiting for: usbus2
Root mount waiting for: usbus2
Root mount waiting for: usbus2
Root mount waiting for: usbus2
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_TIMEOUT, ignored)
ugen2.2: <Unknown> at usbus2 (disconnected)
uhub_reattach_port: could not allocate new device
Trying to mount root from ufs:/dev/ada0s2a [rw]...
drm0: <Intel i965GM> on vgapci0
info: [drm] MSI enabled 1 message(s)
info: [drm] AGP at 0xd0000000 256MB
info: [drm] Initialized i915 1.6.0 20080730
pid 46752 (gcj-dbtool), uid 0: exited on signal 6 (core dumped)

How can I solve this problem !? Thanks in advance.
 
You must log in or register to reply here.
Back
Top