Hi,
I have a server with 3 disks. I installed smartmontools and added
to the /etc/perdiodic.conf file.
In the daily reports i receive, the results are not showed in the same manner.
For ad4 and ad6 disks the results are like this
Whereas, the result for the ad1 disk is
I added at the end of /usr/local/etc/smartd.conf file :
The diference between the 3 disks is that ad1 is an ide disk and ad4 and ad6 are sata disks.
I don't see any error for ad1 so i don't understand why the result isn't just
.
I have another server with 4 ide disks and the results are showed in an another manner with a smartd.conf similar to the the first server
Maybe someone can explain me why the results are different and what to do to have similar results for all drives.
Thanks.
I have a server with 3 disks. I installed smartmontools and added
Code:
daily_status_smart_devices="/dev/ad1 /dev/ad4 /dev/ad6"In the daily reports i receive, the results are not showed in the same manner.
For ad4 and ad6 disks the results are like this
Code:
Checking health of /dev/ad4: OK
Checking health of /dev/ad6: OKWhereas, the result for the ad1 disk is
Code:
Checking health of /dev/ad1: === START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10 family
Device Model: ST3250820A
Serial Number: 9QE7QF99
Firmware Version: 3.AAF
User Capacity: 250,059,350,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Aug 16 03:03:42 2010 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 088 006 Pre-fail Always - 151475299
3 Spin_Up_Time 0x0003 098 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 46
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 089 060 030 Pre-fail Always - 843353840
9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 15979
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 54
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 040 045 Old_age Always In_the_past 39 (Lifetime Min/Max 37/42)
194 Temperature_Celsius 0x0022 039 060 000 Old_age Always - 39 (0 20 0 0)
195 Hardware_ECC_Recovered 0x001a 061 058 000 Old_age Always - 132543123
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 11826 -
# 2 Short offline Completed without error 00% 11734 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.I added at the end of /usr/local/etc/smartd.conf file :
Code:
/dev/ad1 -a -m my@mail.addr
/dev/ad4 -a -m my@mail.addr
/dev/ad6 -a -m my@mail.addrThe diference between the 3 disks is that ad1 is an ide disk and ad4 and ad6 are sata disks.
I don't see any error for ad1 so i don't understand why the result isn't just
Code:
Checking health of /dev/ad1: OKI have another server with 4 ide disks and the results are showed in an another manner with a smartd.conf similar to the the first server
Code:
Checking health of /dev/ad0:
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
Checking health of /dev/ad2:
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
...Maybe someone can explain me why the results are different and what to do to have similar results for all drives.
Thanks.