I am using the latest raspberry pi B image which is 11.1-RELEASE FreeBSD
When it boots no service messages are displayed on screen and very little apart from kernel messages.
I have tried adding to /etc/rc.conf
and creating a /boot/loader.conf.local with:
Which still does not display normal startup messages.
if I run:
I get:
So I would expect a cron starting message and sshd starting message at least.
But I only get the same output as /var/run/dmesg.boot which is:
When it boots no service messages are displayed on screen and very little apart from kernel messages.
I have tried adding to /etc/rc.conf
Bash:
rc_debug="YES"
rc_info="YES"and creating a /boot/loader.conf.local with:
Bash:
verbose_loading="YES"
boot_verbose="YES"Which still does not display normal startup messages.
if I run:
Bash:
service -veI get:
Bash:
/etc/rc.d/growfs
/etc/rc.d/hostid
/etc/rc.d/hostid_save
/etc/rc.d/cleanvar
/etc/rc.d/ip6addrctl
/etc/rc.d/netif
/etc/rc.d/devd
/etc/rc.d/newsyslog
/etc/rc.d/syslogd
/etc/rc.d/savecore
/etc/rc.d/dmesg
/etc/rc.d/virecover
/etc/rc.d/motd
/etc/rc.d/rctl
/etc/rc.d/sshd
/etc/rc.d/cron
/etc/rc.d/mixer
/etc/rc.d/gptboot
/etc/rc.d/bgfsckSo I would expect a cron starting message and sshd starting message at least.
But I only get the same output as /var/run/dmesg.boot which is:
Bash:
Copyright (c) 1992-2017 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.1-RELEASE #0 r321309: Fri Jul 21 13:49:56 UTC 2017
root@releng2.nyi.freebsd.org:/usr/obj/arm.armv6/usr/src/sys/RPI-B arm
FreeBSD clang version 4.0.0 (tags/RELEASE_400/final 297347) (based on LLVM 4.0.0)
VT: init without driver.
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a20000.
CPU: ARM ARM1176 r0p7 (ECO: 0x00000000)
CPU Features:
Thumb, Security, VMSAv7
Optional instructions:
UMULL, SMULL, MLA, SIMD(ext)
16KB/32B 4-way instruction cache
16KB/32B 4-way WB data cache
real memory = 234876928 (223 MB)
avail memory = 218378240 (208 MB)
Physical memory chunk(s):
0x00001000 - 0x0dffffff, 223 MB ( 57343 pages)
Excluded memory regions:
0x00400000 - 0x00e44fff, 10 MB ( 2629 pages) NoAlloc
0x0e000000 - 0x0fffffff, 32 MB ( 8192 pages) NoAlloc NoDump
Static device mappings:
0x20000000 - 0x20ffffff mapped at VA 0xfef00000
random: entropy device external interface
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
crypto: <crypto core>
null: <full device, null device, zero device>
openfirm: <Open Firmware control device>
kbd0 at kbdmux0
mem: <memory>
nfslock: pseudo-device
random: harvesting attach, 8 bytes (4 bits) from nexus0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> mem 0x20000000-0x20ffffff on ofwbus0
simplebus0: Malformed reg property on <vc_mem>
random: harvesting attach, 8 bytes (4 bits) from simplebus0
random: harvesting attach, 8 bytes (4 bits) from ofwbus0
intc0: <BCM2835 Interrupt Controller> mem 0xb200-0xb3ff on simplebus0
simplebus0: no default resources for rid = 0, type = 1
random: harvesting attach, 8 bytes (4 bits) from intc0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
random: harvesting attach, 8 bytes (4 bits) from cpufreq0
random: harvesting attach, 8 bytes (4 bits) from bcm2835_cpufreq0
random: harvesting attach, 8 bytes (4 bits) from cpu0
random: harvesting attach, 8 bytes (4 bits) from cpulist0
systimer0: <BCM2835 System Timer> mem 0x3000-0x3fff irq 0,1,2,3 on simplebus0
Event timer "BCM2835-3" frequency 1000000 Hz quality 1000
Timecounter "BCM2835-3" frequency 1000000 Hz quality 1000
random: harvesting attach, 8 bytes (4 bits) from systimer0
simplebus0: <armtimer> mem 0xb400-0xb423 irq 4 compat broadcom,bcm2835-sp804 (no driver attached)
bcmwd0: <BCM2708/2835 Watchdog> mem 0x10001c-0x100027 on simplebus0
random: harvesting attach, 8 bytes (4 bits) from bcmwd0
gpio0: <BCM2708/2835 GPIO controller> mem 0x200000-0x2000af irq 5,6,7,8 on simplebus0
gpio0: read-only pins: 46-53.
gpio0: reserved pins: 48-53.
gpiobus0: <OFW GPIO bus> on gpio0
random: harvesting attach, 8 bytes (4 bits) from gpiobus0
gpioc0: <GPIO controller> on gpio0
random: harvesting attach, 8 bytes (4 bits) from gpioc0
random: harvesting attach, 8 bytes (4 bits) from gpio0
iichb0: <BCM2708/2835 BSC controller> mem 0x205000-0x20501f irq 9 on simplebus0
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
random: harvesting attach, 8 bytes (4 bits) from iic0
random: harvesting attach, 8 bytes (4 bits) from iicbus0
random: harvesting attach, 8 bytes (4 bits) from iichb0
iichb1: <BCM2708/2835 BSC controller> mem 0x804000-0x80401f irq 10 on simplebus0
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
random: harvesting attach, 8 bytes (4 bits) from iic1
random: harvesting attach, 8 bytes (4 bits) from iicbus1
random: harvesting attach, 8 bytes (4 bits) from iichb1
spi0: <BCM2708/2835 SPI controller> mem 0x204000-0x20401f irq 11 on simplebus0
spibus0: <OFW SPI bus> on spi0
random: harvesting attach, 8 bytes (4 bits) from spibus0
random: harvesting attach, 8 bytes (4 bits) from spi0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7000-0x7fff,0xe05000-0xe05fff irq 12,13,14,15,16,17,18,19,20,21,22,23,24 on simplebus0
random: harvesting attach, 8 bytes (4 bits) from bcm_dma0
mbox0: <BCM2835 VideoCore Mailbox> mem 0xb880-0xb8bf irq 25 on simplebus0
random: harvesting attach, 8 bytes (4 bits) from mbox0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x300000-0x3000ff irq 26 on simplebus0
sdhci_bcm0: SDHCI frequency: 250MHz
sdhci_bcm0-slot0: 250MHz HS 4bits VDD: 3.3V 1.8V VCCQ: 3.3V DRV: B PIO
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x01ff0000 | Host ctl: 0x00000000
sdhci_bcm0-slot0: Power: 0x00000000 | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00000000
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000040
sdhci_bcm0-slot0: Int enab: 0x01ff00fb | Sig enab: 0x01ff00fb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2: 0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr: 0x00000000 | Slot int: 0x00000001
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Card inserted
mmc0: <MMC/SD bus> on sdhci_bcm0
random: harvesting attach, 8 bytes (4 bits) from mmc0
random: harvesting attach, 8 bytes (4 bits) from sdhci_bcm0
uart0: <PrimeCell UART (PL011)> mem 0x201000-0x201fff irq 27 on simplebus0
uart0: console (115200,n,8,1)
uart0: fast interrupt
uart0: PPS capture mode: DCDinvalid
random: harvesting attach, 8 bytes (4 bits) from uart0
vchiq0: <BCM2835 VCHIQ> mem 0xb800-0xb84f irq 28 on simplebus0
vchiq: local ver 8 (min 3), remote ver 8.
pcm0: <VCHIQ audio> on vchiq0
random: harvesting attach, 8 bytes (4 bits) from pcm0
random: harvesting attach, 8 bytes (4 bits) from vchiq0
bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x980000-0x99ffff irq 29 on simplebus0
usbus0 on bcm283x_dwcotg0
bcm283x_dwcotg0: usbpf: Attached
random: harvesting attach, 8 bytes (4 bits) from usbus0
random: harvesting attach, 8 bytes (4 bits) from bcm283x_dwcotg0
fb0: <BCM2835 VT framebuffer driver> on ofwbus0
fbd0 on fb0
VT: initialize with new VT driver "fb".
random: harvesting attach, 8 bytes (4 bits) from fbd0
fb0: 1824x984(1824x984@0,0) 24bpp
fb0: fbswap: 1, pitch 5472, base 0x0e359000, screen_size 5428224
random: harvesting attach, 8 bytes (4 bits) from fb0
ofwbus0: <rpi_ft5406> compat rpi,rpi-ft5406 (no driver attached)
gpioled0: <GPIO LEDs> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from gpioled0
ofwbus0: <regulator> compat broadcom,bcm2835-power-mgr (no driver attached)
cryptosoft0: <software crypto>
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
random: harvesting attach, 8 bytes (4 bits) from cryptosoft0
procfs registered
Timecounters tick every 1.000 msec
lo0: bpf attached
IPsec: Initialized Security Association Processing.
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 2048
usbus0: 480Mbps High Speed USB v2.0
bcm2835_cpufreq0: Boot settings:
bcm2835_cpufreq0: current ARM 700MHz, Core 250MHz, SDRAM 400MHz, Turbo OFF
bcm2835_cpufreq0: max/min ARM 700/700MHz, Core 250/250MHz, SDRAM 400/400MHz
bcm2835_cpufreq0: current Core 30001200mV, SDRAM_C 30001200mV, SDRAM_I 30001200mV, SDRAM_P 30001200mV
bcm2835_cpufreq0: max/min Core 30001200/30001200mV, SDRAM_C 30001200/30001200mV, SDRAM_I 30001200/30001200mV, SDRAM_P 30001200/30001200mV
bcm2835_cpufreq0: Temperature 47.0C
ugen0.1: <DWCOTG OTG Root HUB> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
sdhci_bcm0-slot0: Divider 313 for freq 399361 (base 250000000)
mmc0: Probing bus
mmc0: SD 2.0 interface conditions: OK
mmc0: SD probe: OK (OCR: 0x40ff8000)
mmc0: Current OCR: 0x00ff8000
mmc0: Probing cards
mmc0: New card detected (CID 1b534d454231515430754553a5012300)
mmc0: New card detected (CSD 400e00325b590000ee7f7f800a404000)
mmc0: Card at relative address 0x0001 added:
mmc0: card: SDHC EB1QT 3.0 SN 754553A5 MFG 03/2018 by 27 SM
mmc0: bus: 4bit, 50MHz (high speed timing)
mmc0: memory: 62521344 blocks, erase sector 8192 blocks
uhub0: 1 port with 1 removable, self powered
random: harvesting attach, 8 bytes (4 bits) from uhub0
mmc0: setting transfer rate to 50.000MHz (high speed timing)
sdhci_bcm0-slot0: Divider 3 for freq 41666666 (base 250000000)
mmcsd0: 32GB <SDHC EB1QT 3.0 SN 754553A5 MFG 03/2018 by 27 SM> at mmc0 41.6MHz/4bit/65535-block
random: harvesting attach, 8 bytes (4 bits) from mmcsd0
pcm0: Mixer "vol":
Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
GEOM: new disk mmcsd0
mmc0: setting bus width to 4 bits high speed timing
GEOM_PART: partition 1 on (mmcsd0, MBR) is not aligned on 4194304 bytes
GEOM_PART: partition 2 on (mmcsd0, MBR) is not aligned on 4194304 bytes
ugen0.2: <vendor 0x0424 product 0x9512> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x0424 product 0x9512, class 9/0, rev 2.00/2.00, addr 2> on usbus0
uhub1: MTT enabled
GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 bytes
GEOM_PART: partition 1 on (diskid/DISK-754553A5, MBR) is not aligned on 4194304 bytes
GEOM_PART: partition 2 on (diskid/DISK-754553A5, MBR) is not aligned on 4194304 bytes
uhub1: 3 ports with 2 removable, self powered
random: harvesting attach, 8 bytes (4 bits) from uhub1
GEOM_PART: partition 1 on (diskid/DISK-754553A5s2, BSD) is not aligned on 4194304 bytes
warning: no time-of-day clock registered, system time will not be set accurately
start_init: trying /sbin/init
ugen0.3: <vendor 0x0424 product 0xec00> at usbus0
smsc0 on uhub1
smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0
random: harvesting attach, 8 bytes (4 bits) from smsc0
smsc0: chip 0xec00, rev. 0002
miibus0: <MII bus> on smsc0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0: OUI 0x00800f, model 0x000c, rev. 3
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy0
random: harvesting attach, 8 bytes (4 bits) from miibus0
ue0: <USB Ethernet> on smsc0
ue0: bpf attached
ue0: Ethernet address: b8:27:eb:a4:99:c9
GEOM_PART: partition 1 on (diskid/DISK-754553A5, MBR) is not aligned on 4194304 bytes
GEOM_PART: partition 2 on (diskid/DISK-754553A5, MBR) is not aligned on 4194304 bytes
GEOM_PART: partition 1 on (diskid/DISK-754553A5s2, BSD) is not aligned on 4194304 bytes
random: unblocking device.
smsc0: chip 0xec00, rev. 0002
ue0: link state changed to DOWN
ue0: link state changed to UP