FreeBSD v12 -p10 UEFI TRI boot Linux on UTC net update and win10 that is just win10. I don't really use it, I just keep it installed for a just in case situation, nod my time never gets updated it is , still.
I added the
server 0.us.pool.ntp.org iburst
because the FreeBSD one wasn't working.
it is 5 hours a head of time
what am I missing???
########################
I just did this and I do not know what effect it will have on the time/date
I added the
server 0.us.pool.ntp.org iburst
because the FreeBSD one wasn't working.
it is 5 hours a head of time
Code:
$ ntpq -c peer
remote refid st t when poll reach delay offset jitter
==============================================================================
*eterna.binary.n 128.252.19.1 2 u 4 64 3 32.439 -0.923 5.613
+t1.time.gq1.yah 208.71.46.33 2 u 58 64 1 81.690 -0.499 10.233
-srcf-ntp.stanfo 171.64.7.73 2 u 3 64 3 62.391 2.729 10.733
+christensenplac 209.51.161.238 2 u 59 64 1 51.614 0.030 2.121
Code:
$ cat /etc/rc.conf
clear_tmp_enable="YES"
syslogd_flags="-ss"
openntpd_flags="-s"
sendmail_enable="NONE"
hostname="FreeBSD64.net"
wlans_iwm0="wlan0"
ifconfig_wlan0="WPA SYNCDHCP"
create_args_wlan0="country US regdomain FCC"
#sshd_enable="YES"
#time set on line
ntpd_enable="YES"
ntpd_sync_on_start="YES"
ntpdate_enable="YES"
#powerd_enable="YES"
# Set dumpdev to "AUTO" to enable crash dumps, "NO" to disable
dumpdev="AUTO"
kld_list="/boot/modules/i915kms.ko"
slim_enable="YES"
ifconfig_em0="DHCP"
devfs_system_ruleset="localrules"
autofs_enable="YES"
dbus_enable="YES"
Code:
userx@FreeBSD64.net:~
$ cat /etc/ntp.conf
#
# $FreeBSD: releng/12.0/usr.sbin/ntp/ntpd/ntp.conf 337649 2018-08-11 17:42:42Z brd $
#
# Default NTP servers for the FreeBSD operating system.
#
# Don't forget to enable ntpd in /etc/rc.conf with:
# ntpd_enable="YES"
#
# The driftfile is by default /var/db/ntpd.drift, check
# /etc/defaults/rc.conf on how to change the location.
#
#
# Set the target and limit for adding servers configured via pool statements
# or discovered dynamically via mechanisms such as broadcast and manycast.
# Ntpd automatically adds maxclock-1 servers from configured pools, and may
# add as many as maxclock*2 if necessary to ensure that at least minclock
# servers are providing good consistant time.
#
tos minclock 3 maxclock 6
#
# The following pool statement will give you a random set of NTP servers
# geographically close to you. A single pool statement adds multiple
# servers from the pool, according to the tos minclock/maxclock targets.
# See http://www.pool.ntp.org/ for details. Note, pool.ntp.org encourages
# users with a static IP and good upstream NTP servers to add a server
# to the pool. See http://www.pool.ntp.org/join.html if you are interested.
#
# The option `iburst' is used for faster initial synchronization.
#
#pool 0.freebsd.pool.ntp.org iburst
#
# If you want to pick yourself which country's public NTP server
# you want to sync against, comment out the above pool, uncomment
# the next one, and replace CC with the country's abbreviation.
# Make sure that the hostname resolves to a proper IP address!
#
# pool 0.CC.pool.ntp.org iburst
server 0.us.pool.ntp.org iburst
server 1.us.pool.ntp.org iburst
server 2.us.pool.ntp.org iburst
server 3.us.pool.ntp.org iburst
#
# To configure a specific server, such as an organization-wide local
# server, add lines similar to the following. One or more specific
# servers can be configured in addition to, or instead of, any server
# pools specified above. When both are configured, ntpd first adds all
# the specific servers, then adds servers from the pool until the tos
# minclock/maxclock targets are met.
#
#server time.my-internal.org iburst
#
# Security:
#
# By default, only allow time queries and block all other requests
# from unauthenticated clients.
#
# The "restrict source" line allows peers to be mobilized when added by
# ntpd from a pool, but does not enable mobilizing a new peer association
# by other dynamic means (broadcast, manycast, ntpq commands, etc).
#
# See http://support.ntp.org/bin/view/Support/AccessRestrictions
# for more information.
#
restrict default limited kod nomodify notrap noquery nopeer
restrict source limited kod nomodify notrap noquery
#
# Alternatively, the following rules would block all unauthorized access.
#
#restrict default ignore
#
# In this case, all remote NTP time servers also need to be explicitly
# allowed or they would not be able to exchange time information with
# this server.
#
# Please note that this example doesn't work for the servers in
# the pool.ntp.org domain since they return multiple A records.
#
#restrict 0.pool.ntp.org nomodify nopeer noquery notrap
#restrict 1.pool.ntp.org nomodify nopeer noquery notrap
#restrict 2.pool.ntp.org nomodify nopeer noquery notrap
#
# The following settings allow unrestricted access from the localhost
restrict 127.0.0.1
restrict ::1
#
# If a server loses sync with all upstream servers, NTP clients
# no longer follow that server. The local clock can be configured
# to provide a time source when this happens, but it should usually
# be configured on just one server on a network. For more details see
# http://support.ntp.org/bin/view/Support/UndisciplinedLocalClock
# The use of Orphan Mode may be preferable.
#
#server 127.127.1.0
#fudge 127.127.1.0 stratum 10
# See http://support.ntp.org/bin/view/Support/ConfiguringNTP#Section_6.14.
# for documentation regarding leapfile. Updates to the file can be obtained
# from ftp://time.nist.gov/pub/ or ftp://tycho.usno.navy.mil/pub/ntp/.
# Use either leapfile in /etc/ntp or periodically updated leapfile in /var/db.
#leapfile "/etc/ntp/leap-seconds"
leapfile "/var/db/ntpd.leap-seconds.list"what am I missing???
########################
I just did this and I do not know what effect it will have on the time/date
Code:
$ sudo tzsetup /usr/share/zoneinfo/America/Chicago
greenwich time zone CLOCK.