LaCie P'9230 USB 3.0 Drive Not Recognized

dougs

dougs

I went out and got a LaCie P'9230 drive, an external USB 3.0/2.0 2TB drive (http://www.lacie.com/products/product.htm?id=10559). FreeBSD 9.0-STABLE #5 running on an Intel D845GEBV2L motherboard does not recognize it.
Code: 
Apr 23 15:57:11 test kernel: usb_alloc_device: set address 2 failed (USB_ERR_STALLED, ignored)
Apr 23 15:57:11 test kernel: usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_STALLED
Apr 23 15:57:12 test kernel: usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_STALLED, ignored)
Apr 23 15:57:12 test kernel: usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_STALLED
Apr 23 15:57:13 test kernel: usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_STALLED, ignored)
Apr 23 15:57:13 test kernel: usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_STALLED
Apr 23 15:57:13 test kernel: ugen3.2: <Unknown> at usbus3 (disconnected)
Apr 23 15:57:13 test kernel: uhub_reattach_port: could not allocate new device
root@test:/usr/home/install#

camcontrol devlist -v does not indicate any daX devices.

I've used a variety of smaller external LaCie USB 2.0 drives with this motherboard successfully in the past.

A link at the LaCie web site (http://www.lacie.com/more/index.htm?id=10112) indicates that a driver needs to be installed on a Mac in order to realize true USB 3.0 speeds. Does this mean that for me to use this drive, I need a special driver?

I've consulted the hardware compatibility list but it appears to not have been updated to reflect newer hardware.

Any advice would be appreciated.

~Doug
 
I don't know if it will make you feel any better, but my WD My Book Essential 2TB drive works fine with FreeBSD 10.0-current when connected to a USB 2.0 port, but fails to configure properly when connected to a USB 3.0 port on the same system. The symptoms and error messages are similar to yours (but with more stuff because debugging is turned on). I haven't tried it with 9-stable yet, but I'll bet it does the same thing as yours.
 
I'm having the same problem with my LaCie P'9230 on 9.3

Error message is slightly different:

Code: 
usb_alloc_device: set address 2 failed (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
ugen5.2: <Unknown> at usbus5 (disconnected)
uhub_reattach_port: could not allocate new device

Has anyone tried 10.1 if this USB disk works there? Any suggestions how to debug the problem?
 
You must log in or register to reply here.
Back
Top