Hi all, I recently bought a M.2 SATA SSD for FreeBSD system. Everything works fine on this disk with ZFS. However, when I ran
This is a weird error and I've not met this before. Besides this, all the parameters of the disk is ok:
Does anyone have ideas about this error? The SSD model is LITEON CV6-8Q128 (V5G).
Thanks in advance!
smartctl -A on this device, I've got some errors as follows:
Code:
SMART Error Log Version: 1
Warning: ATA error count 0 inconsistent with error log pointer 2
ATA Error Count: 0
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error -1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 ec 00 00 00 00 00 Device Fault
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 00 00 00 00 00 00:00:00.000 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1 -
Selective Self-tests/Logging not supportedThis is a weird error and I've not met this before. Besides this, all the parameters of the disk is ok:
Code:
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 000 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0003 100 100 000 Pre-fail Always - 0
9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 12
12 Power_Cycle_Count 0x0003 100 100 000 Pre-fail Always - 18
170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
171 Unknown_Attribute 0x0003 100 100 000 Pre-fail Always - 0
172 Unknown_Attribute 0x0003 100 100 000 Pre-fail Always - 0
173 Unknown_Attribute 0x0003 100 100 000 Pre-fail Always - 0
174 Unknown_Attribute 0x0003 100 100 000 Pre-fail Always - 0
175 Program_Fail_Count_Chip 0x0003 100 100 000 Pre-fail Always - 0
176 Erase_Fail_Count_Chip 0x0003 100 100 000 Pre-fail Always - 0
178 Used_Rsvd_Blk_Cnt_Chip 0x0003 100 100 000 Pre-fail Always - 0
179 Used_Rsvd_Blk_Cnt_Tot 0x0003 100 100 000 Pre-fail Always - 0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033 100 100 005 Pre-fail Always - 23
181 Program_Fail_Cnt_Total 0x0003 100 100 000 Pre-fail Always - 0
182 Erase_Fail_Count_Total 0x0003 100 100 000 Pre-fail Always - 0
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
195 Hardware_ECC_Recovered 0x0003 100 100 000 Pre-fail Always - 0
199 UDMA_CRC_Error_Count 0x0003 100 100 000 Pre-fail Always - 0
232 Available_Reservd_Space 0x0003 100 100 010 Pre-fail Always - 100
233 Media_Wearout_Indicator 0x0003 100 100 000 Pre-fail Always - 669
241 Total_LBAs_Written 0x0003 100 100 000 Pre-fail Always - 425
242 Total_LBAs_Read 0x0003 100 100 000 Pre-fail Always - 36Does anyone have ideas about this error? The SSD model is LITEON CV6-8Q128 (V5G).
Thanks in advance!