intel wifi 5150

braveduck

braveduck

Hello.

I got a Lenovo S12-1n netbook, and it has intel wifi 5150 chip built-in. At least, I believe it to be 5150. As far as I've read, it should be supported under FreeBSD 8.0 by iwn driver. It worked under ArchLinux, the problem is I don't like linux =)


Code: 
uname -a
FreeBSD ulyss.urtext.ru 8.0-RELEASE-p2 FreeBSD 8.0-RELEASE-p2 #0: Thu May 13 18:12:03 EEST 2010     root@ulyss.urtext.ru:/usr/obj/usr/src/sys/ULYSS  i386

And I have put these lines into the kernel config:

Code: 
device          wlan
device          iwn
device          iwnfw
device          firmware
device          pci

Still the device is not detected, there is no iwn0 in ifconfig output.
Any advice would be great.
 
It does not show up at all.

here is the dmesg output

Code: 
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RELEASE-p2 #0: Thu May 13 18:12:03 EEST 2010
    [email]root@ulyss.urtext.ru[/email]:/usr/obj/usr/src/sys/ULYSS
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Atom(TM) CPU N270   @ 1.60GHz (1600.01-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x106c2  Stepping = 2
  Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x40c39d<SSE3,DTES64,MON,DS_CPL,EST,TM2,SSSE3,xTPR,PDCM,<b22>>
  AMD Features=0x100000<NX>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 1073741824 (1024 MB)
avail memory = 891052032 (849 MB)
ACPI APIC Table: <PTLTD          APIC  >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP/HT): APIC ID:  1
ioapic0 <Version 1.1> irqs 0-23 on motherboard
Cuse4BSD v0.1.11 @ /dev/cuse
kbd1 at kbdmux0
acpi0: <LENOVO CB-01> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x47> port 0x62,0x66 on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 25000000 Hz quality 900
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <memory, RAM> at device 0.1 (no driver attached)
isab0: <PCI-ISA bridge> port 0x1c00-0x1cff at device 3.0 on pci0
isa0: <ISA bus> on isab0
pci0: <memory, RAM> at device 3.1 (no driver attached)
pci0: <serial bus, SMBus> at device 3.2 (no driver attached)
pci0: <memory, RAM> at device 3.3 (no driver attached)
pci0: <processor> at device 3.5 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xb0006000-0xb0006fff irq 20 at device 4.0 on pci0
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xb0007000-0xb00070ff irq 21 at device 4.1 on pci0
ehci0: [ITHREAD]
usbus1: EHCI version 1.0
usbus1: <EHCI (generic) USB 2.0 controller> on ehci0
ohci1: <OHCI (generic) USB controller> mem 0xb0008000-0xb0008fff irq 22 at device 6.0 on pci0
ohci1: [ITHREAD]
usbus2: <OHCI (generic) USB controller> on ohci1
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xb0007400-0xb00074ff irq 23 at device 6.1 on pci0
ehci1: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <EHCI (generic) USB 2.0 controller> on ehci1
hdac0: <NVidia MCP79 High Definition Audio Controller> mem 0xb0000000-0xb0003fff irq 17 at device 8.0 on pci0
hdac0: HDA Driver Revision: 20090624_0136
hdac0: [ITHREAD]
pcib1: <ACPI PCI-PCI bridge> at device 9.0 on pci0
pci1: <ACPI PCI bus> on pcib1
atapci0: <nVidia AHCI controller> port 0x30e0-0x30e7,0x30d4-0x30d7,0x30d8-0x30df,0x30d0-0x30d3,0x30c0-0x30cf mem 0xb0004000-0xb0005fff irq 18 at device 11.0 on pci0
atapci0: [ITHREAD]
atapci0: AHCI v1.20 controller with 6 3Gbps ports, PM supported
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: [ITHREAD]
ata6: <ATA channel 4> on atapci0
ata6: [ITHREAD]
ata7: <ATA channel 5> on atapci0
ata7: [ITHREAD]
pcib2: <ACPI PCI-PCI bridge> irq 19 at device 12.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 13.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 14.0 on pci0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 16.0 on pci0
pci5: <ACPI PCI bus> on pcib5
vgapci0: <VGA-compatible display> port 0x4000-0x407f mem 0xb1000000-0xb1ffffff,0xc0000000-0xcfffffff,0xb4000000-0xb5ffffff irq 23 at device 0.0 on pci5
nvidia0: <ION> on vgapci0
vgapci0: child nvidia0 requested pci_enable_busmaster
vgapci0: child nvidia0 requested pci_enable_io
vgapci0: child nvidia0 requested pci_enable_io
nvidia0: [ITHREAD]
pcib6: <ACPI PCI-PCI bridge> irq 20 at device 21.0 on pci0
pci6: <ACPI PCI bus> on pcib6
bge0: <Broadcom BCM5906 A2, ASIC rev. 0xc002> mem 0xb2000000-0xb200ffff irq 20 at device 0.0 on pci6
miibus0: <MII bus> on bge0
brgphy0: <BCM5906 10/100baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bge0: Ethernet address: 00:1f:16:34:9e:8c
bge0: [ITHREAD]
pcib7: <ACPI PCI-PCI bridge> irq 21 at device 22.0 on pci0
pci7: <ACPI PCI bus> on pcib7
pcib8: <ACPI PCI-PCI bridge> irq 22 at device 23.0 on pci0
pci9: <ACPI PCI bus> on pcib8
pci9: <network> at device 0.0 (no driver attached)
pcib9: <ACPI PCI-PCI bridge> at device 24.0 on pci0
pci10: <ACPI PCI bus> on pcib9
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0
atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xcf000-0xd2fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
ppc0: parallel port not found.
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
uart0: [FILTER]
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 480Mbps High Speed USB v2.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
ad4: 152627MB <WDC WD1600BEVT-22ZCT0 11.01A11> at ata2-master SATA300
ugen0.1: <nVidia> at usbus0
uhub0: <nVidia OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <nVidia> at usbus1
uhub1: <nVidia EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ugen2.1: <nVidia> at usbus2
uhub2: <nVidia OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <nVidia> at usbus3
uhub3: <nVidia EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
uhub0: 6 ports with 6 removable, self powered
uhub2: 6 ports with 6 removable, self powered
hdac0: HDA Codec #0: Realtek ALC269
hdac0: HDA Codec #3: NVidia MCP7A HDMI
GEOM: ad4: partition 3 does not start on a track boundary.
GEOM: ad4: partition 3 does not end on a track boundary.
pcm0: <HDA Realtek ALC269 PCM #0 Analog> at cad 0 nid 1 on hdac0
pcm1: <HDA NVidia MCP7A HDMI PCM #0 Digital> at cad 3 nid 1 on hdac0
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus3 usbus1
Root mount waiting for: usbus3 usbus1
uhub1: 6 ports with 6 removable, self powered
uhub3: 6 ports with 6 removable, self powered
Root mount waiting for: usbus3 usbus1
Root mount waiting for: usbus3 usbus1
ugen1.2: <BISON Corporation> at usbus1
usb_alloc_device:1624: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT!
pcm0: <HDA Realtek ALC269 PCM #0 Analog> at cad 0 nid 1 on hdac0
pcm1: <HDA NVidia MCP7A HDMI PCM #0 Digital> at cad 3 nid 1 on hdac0
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus3 usbus1
Root mount waiting for: usbus3 usbus1
uhub1: 6 ports with 6 removable, self powered
uhub3: 6 ports with 6 removable, self powered
Root mount waiting for: usbus3 usbus1
Root mount waiting for: usbus3 usbus1
ugen1.2: <BISON Corporation> at usbus1
usb_alloc_device:1624: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT!
Root mount waiting for: usbus3
Root mount waiting for: usbus3
usbd_req_re_enumerate:1553: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT!
Root mount waiting for: usbus3
Root mount waiting for: usbus3
usbd_req_re_enumerate:1553: getting device descriptor at addr 2 failed, USB_ERR_TIMEOUT!
ugen3.2: <(null)> at usbus3 (disconnected)
uhub_reattach_port:435: could not allocate new device!
Trying to mount root from ufs:/dev/ad4s1a
Setting hostuuid: fd263400-e541-11de-aaeb-f3c02bb60e22.
Setting hostid: 0x9c3bedca.

and pciconf -lv says

Code: 
none5@pci0:9:0:0:	class=0x028000 card=0x12168086 chip=0x423d8086 rev=0x00 hdr=0x00
vendor     = 'Intel Corporation'
class      = network
 
According to iwn(5) (assuming that that is indeed the driver needed for your Intel card), you need to load specific firmware.

Code: 
     You also need to select a firmware for your device.  Choose one from:

           device iwn4965fw
           device iwn5000fw
           device iwn5100fw

A quick search on my system even produced:
Code: 
/boot/kernel/iwn5150fw.ko
 
Thank you, I should've searched the forums more thoroughly, as I've found it was mentioned in another thread. It works now with the driver from svn. Thanks again.
 
You must log in or register to reply here.
Back
Top