Installing FreeBSD on a Z83 Mini PC

B

balanga

Have managed to run FreeBSD on a Z83 Mini PC using an external disk, but I was wondering if it possible to actually install it on the device... Has anyone tried/succeeded?

Reading through this guide I'm not entirely sure if someone actually installed Linux on one of these things or just used it to boot from an external drive, but if they did manage to install it, presumably FreeBSD could also be installed...
 
A possible problem might be if the eMMC / eMMC controller isn't supported by FreeBSD. Somebody with one of these needs to boot FreeBSD on it and check...
 
tingo said:
A possible problem might be if the eMMC / eMMC controller isn't supported by FreeBSD. Somebody with one of these needs to boot FreeBSD on it and check...
Click to expand...
I have one of these and can boot an external drive from it, but I'd like to be able to install FreeBSD on the thing itself.

Would the output from dmesg be of any use?
 
Yes, it might tell us if the eMMC is supported. Relevant parts of# pciconf -lv output might also be helpful.
 
pciconf -lv
Code: 
hostb0@pci0:0:0:0:      class=0x060000 card=0x72708086 chip=0x22808086 rev=0x36 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series SoC Transaction Register'
    class      = bridge
    subclass   = HOST-PCI
vgapci0@pci0:0:2:0:     class=0x030000 card=0x72708086 chip=0x22b08086 rev=0x36 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Configuration Registers'
    class      = display
    subclass   = VGA
none0@pci0:0:11:0:      class=0x118000 card=0x72708086 chip=0x22dc8086 rev=0x36 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Power Management Controller'
    class      = dasp
xhci0@pci0:0:20:0:      class=0x0c0330 card=0x72708086 chip=0x22b58086 rev=0x36 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series USB xHCI Controller'
    class      = serial bus
    subclass   = USB
none1@pci0:0:26:0:      class=0x108000 card=0x72708086 chip=0x22988086 rev=0x36 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Trusted Execution Engine'
    class      = encrypt/decrypt
pcib1@pci0:0:28:0:      class=0x060400 card=0x72708086 chip=0x22c88086 rev=0x36 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Express Port'
    class      = bridge
    subclass   = PCI-PCI
isab0@pci0:0:31:0:      class=0x060100 card=0x72708086 chip=0x229c8086 rev=0x36 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCU'
    class      = bridge
    subclass   = PCI-ISA
re0@pci0:1:0:0: class=0x020000 card=0x012310ec chip=0x816810ec rev=0x0c hdr=0x00
    vendor     = 'Realtek Semiconductor Co., Ltd.'
    device     = 'RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller'
    class      = network
    subclass   = ethernet

dmesg
Code: 
---<<BOOT>>---
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-RELEASE r341666 GENERIC amd64
FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on LLVM 6.0.1)
VT: init without driver.
CPU: Intel(R) Atom(TM) x5-Z8350  CPU @ 1.44GHz (1440.00-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x406c4  Family=0x6  Model=0x4c  Stepping=4
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x43d8e3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,TSCDLT,AESNI,RDRAND>
  AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
  AMD Features2=0x101<LAHF,Prefetch>
  Structured Extended Features=0x2282<TSCADJ,SMEP,ERMS,NFPUSG>
  VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID
  TSC: P-state invariant, performance statistics
real memory  = 2147483648 (2048 MB)
avail memory = 1966039040 (1874 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I >
WARNING: L1 data cache covers fewer APIC IDs than a core (0 < 1)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
random: unblocking device.
ioapic0 <Version 2.0> irqs 0-114 on motherboard
Launching APs: 3 2 1
Timecounter "TSC" frequency 1440004680 Hz quality 1000
random: entropy device external interface
kbd1 at kbdmux0
netmap: loaded module
[ath_hal] loaded
module_register_init: MOD_LOAD (vesa, 0xffffffff810f9770, 0) error 19
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
nexus0
efirtc0: <EFI Realtime Clock> on motherboard
efirtc0: registered as a time-of-day clock, resolution 1.000000s
cryptosoft0: <software crypto> on motherboard
acpi0: <ALASKA A M I > on motherboard
acpi0: Power Button (fixed)
unknown: I/O range not supported
cpu0: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
atrtc0: Warning: Couldn't map I/O.
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 8 on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 450
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0x90000000-0x90ffffff,0x80000000-0x8fffffff at device 2.0 on pci0
vgapci0: Boot video device
xhci0: <Intel Braswell USB 3.0 controller> mem 0x91500000-0x9150ffff at device 20.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
usbus0 on xhci0
usbus0: 5.0Gbps Super Speed USB v3.0
pci0: <encrypt/decrypt> at device 26.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0x91404000-0x91404fff,0x91400000-0x91403fff at device 0.0 on pci1
re0: Using 1 MSI-X message
re0: turning off MSI enable bit.
re0: Chip rev. 0x4c000000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8251/8153 1000BASE-T media interface> PHY 1 on miibus0
rgephy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: 84:39:be:64:3a:cc
re0: netmap queues/slots: TX 1/256, RX 1/256
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
acpi_button0: <Power Button> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
sdhci_acpi0: <Intel Bay Trail/Braswell eMMC 4.5/4.5.1 Controller> iomem 0x9153a000-0x9153afff irq 45 on acpi0
mmc0: <MMC/SD bus> on sdhci_acpi0
sdhci_acpi1: <Intel Bay Trail/Braswell SDXC Controller> iomem 0x91536000-0x91536fff irq 47 on acpi0
mmc1: <MMC/SD bus> on sdhci_acpi1
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbdc0: non-PNP ISA device will be removed from GENERIC in FreeBSD 12.
est0: <Enhanced SpeedStep Frequency Control> on cpu0
ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is present;
            to enable, add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf.
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
ugen0.1: <0x8086 XHCI root HUB> at usbus0
uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
mmcsd0: 31GB <MMCHC NCard  3.9 SN 06E47059 MFG 08/2016 by 136 0x0003> at mmc0 200.0MHz/8bit/8192-block
mmcsd0boot0: 4MB partion 1 at mmcsd0
mmcsd0boot1: 4MB partion 2 at mmcsd0
mmcsd0rpmb: 4MB partion 3 at mmcsd0
mmc1: No compatible cards found on bus
Trying to mount root from zfs:zroot/ROOT/default []...
Root mount waiting for: usbus0
uhub0: 13 ports with 13 removable, self powered
Root mount waiting for: usbus0
ugen0.2: <Dell Dell USB Keyboard> at usbus0
ukbd0 on uhub0
ukbd0: <Dell Dell USB Keyboard, class 0/0, rev 1.10/3.01, addr 1> on usbus0
kbd2 at ukbd0
Root mount waiting for: usbus0
ugen0.3: <Samsung M3 Portable Samsung M3 Portable> at usbus0
umass0 on uhub0
umass0: <MSC Bulk-Only Transport> on usbus0
umass0:  SCSI over Bulk-Only; quirks = 0x8100
umass0:0:0: Attached to scbus0
da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
da0: <Samsung M3 Portable 1404> Fixed Direct Access SPC-4 SCSI device
da0: Serial Number 97DE7DF51200008F
da0: 400.000MB/s transfers
da0: 1907729MB (3907029168 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
Solaris: NOTICE: Cannot find the pool label for 'zroot'
Mounting from zfs:zroot/ROOT/default failed with error 5; retrying for 3 more seconds
drmn0: <drmn> on vgapci0
vgapci0: child drmn0 requested pci_enable_io
vgapci0: child drmn0 requested pci_enable_io
[drm] Unable to create a private tmpfs mount, hugepage support will be disabled(-19).
Successfully added WC MTRR for [0x80000000-0x8fffffff]: 0;
[drm] Got stolen memory base 0x7cc00000, size 0x2000000
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] Driver supports precise vblank timestamp query.
[drm] Connector eDP-1: get mode from tunables:
[drm]   - kern.vt.fb.modes.eDP-1
[drm]   - kern.vt.fb.default_mode
[drm] failed to retrieve link info, disabling eDP
[drm] Connector HDMI-A-1: get mode from tunables:
[drm]   - kern.vt.fb.modes.HDMI-A-1
[drm]   - kern.vt.fb.default_mode
[drm] Connector DP-1: get mode from tunables:
[drm]   - kern.vt.fb.modes.DP-1
[drm]   - kern.vt.fb.default_mode
[drm] Connector HDMI-A-2: get mode from tunables:
[drm]   - kern.vt.fb.modes.HDMI-A-2
[drm]   - kern.vt.fb.default_mode
[drm] Initialized i915 1.6.0 20171222 for drmn0 on minor 0
fuse-freebsd: version 0.4.4, FUSE ABI 7.8
lo0: link state changed to UP
re0: link state changed to DOWN
re0: link state changed to UP
VT: initialize with new VT driver "fb".
start FB_INFO:
type=11 height=1080 width=1920 depth=32
cmsize=16 size=8294400
pbase=0x80020000 vbase=0xfffff80080020000
name=drmn0 flags=0x0 stride=7680 bpp=32
cmap[0]=0 cmap[1]=7f0000 cmap[2]=7f00 cmap[3]=c4a000
end FB_INFO
drmn0: fb0: inteldrmfb frame buffer device
 
So, you have
Code: 
sdhci_acpi0: <Intel Bay Trail/Braswell eMMC 4.5/4.5.1 Controller> iomem 0x9153a000-0x9153afff irq 45 on acpi0
mmc0: <MMC/SD bus> on sdhci_acpi0
sdhci_acpi1: <Intel Bay Trail/Braswell SDXC Controller> iomem 0x91536000-0x91536fff irq 47 on acpi0
mmc1: <MMC/SD bus> on sdhci_acpi1
not one, but two eMMC controllers, and it looks like they are supported.
Further down
Code: 
mmcsd0: 31GB <MMCHC NCard  3.9 SN 06E47059 MFG 08/2016 by 136 0x0003> at mmc0 200.0MHz/8bit/8192-block
mmcsd0boot0: 4MB partion 1 at mmcsd0
mmcsd0boot1: 4MB partion 2 at mmcsd0
mmcsd0rpmb: 4MB partion 3 at mmcsd0
mmc1: No compatible cards found on bus
OK, just one eMMC (mmcsd0), nothing for mmc1. You should try gpart show -p mmcsd0 to chek that gpart can read it (it should).
 
Last edited:
Revisiting an old thread after stumbling on my old Z83 Mini PC, I wondered if anything had changed with the anouncement of 14.0-R...

Do I simply need to add set hint.ppc.0.disabled="1" to /boot/device.hints to get the thing booting?
 
balanga said:
Revisiting an old thread after stumbling on my old Z83 Mini PC, I wondered if anything had changed with the anouncement of 14.0-R...

Do I simply need to add set hint.ppc.0.disabled="1" to /boot/device.hints to get the thing booting?
Click to expand...
Yes and 13.2 is the same. I have a few of these systems X5-z8350 and X5-z8300 and both boot 13.2 Release with the hint set.
 
balanga said:
Do I simply need to add set hint.ppc.0.disabled="1" to /boot/device.hints to get the thing booting?
Click to expand...
set hint.ppc.0.disabled="1" is the command to run at the loader prompt.
set <That is the loader trigger command.

For /boot/device.hints you do not add 'set'
hint.ppc.0.disabled="1"

Just look at the other entries. There are no set commands here.
 
I have two beelink machines that are emmc the others are dell 3040 thin clients and I run them on USB storage. I have FreeBSD 13.2 installed.
 
You must log in or register to reply here.
Back
Top