Search results

  1. M

    interface 'flipping' @ boot

    I changed the cable and port. I know I had to change ONE thing at a time. I'll put back the new cable on the original port later. Now I have : em0: link state changed to UP em0: link state changed to DOWN em0: promiscuous mode enabled em0: link state changed to UP em0: link state changed to...
  2. M

    interface 'flipping' @ boot

    So, it happen after a cold boot; never tried to suspend so far. On the other end there is a switch/router with other ports yes. I'll try another port and if it's the same thing, another cable. This particular cable is comming from the router, dont lay on ground, and was used for other devices...
  3. M

    interface 'flipping' @ boot

    Hi there, I have a strange network interface init behaviour. In the end the interface is up and running ... most of the time. Configuration is DHCP. The computer is a Dell laptop I use for work. Here is the behaviour : dmesg | grep em0 ahciem0: <AHCI enclosure management bridge> on ahci0 em0...
  4. M

    bhyve vm-bhyve and debian

    Ok, got it, thanks for the tip. So I had to switch from grub to uefi and do post install as stated. My config file now is : loader="uefi" cpu=2 memory=1G graphics="yes" network0_type="virtio-net" network0_switch="vswitch1" disk0_type="ahci-hd" disk0_name="disk0.img"...
  5. M

    bhyve vm-bhyve and debian

    Hello, I tried a good number of times but can succeed to boot debian 11 vm in bhyve. Installation is ok, disk and network are detected and are ok but upon reboot I just get : grub> I use vm-bhyve with all defaults outside switch name. Config file is like this : loader="grub" cpu=2 memory=1G...
  6. M

    bhyve Ryzen 7 Boost

    I looked carefully in bios and saw only 'enable cpu boost' set to 'auto' (out of 'auto' or 'disable'). No specific other boost parameter. I will do as you advice, try to change one thing, try to stress test the OS and then do with the next parameter. And no, never seen boost in the OS itself so...
  7. M

    bhyve Ryzen 7 Boost

    I changed my setup a little : powerd_enable="YES" powerd_flags="-a hiadaptive -b hiadaptive -n hiadaptive -m 1800 -M 4200 -i 30 -r 50" performance_cpu_freq="NONE" performance_cx_lowest="LOW" economy_cpu_freq="NONE" economy_cx_lowest="LOW" and in loader.conf : hint.apic.0.clock=0...
  8. M

    bhyve Ryzen 7 Boost

    Hello, I just installed FreeBSD 13.1 with Bhyve and vm-bhyve. I, somehow, managed to get Windows 10 vm running ok. My CPU is a Ryzen 7 4800U witch has 8 cores / 16 threads. This Ryzen frequency is 1.8 GHz base and 4.2 GHz boost. I try hard to get any boost on the Windows vm but cant manage to...
  9. M

    bhyve Bhyve graphical control panel

    Sure, like I say in the first post I'm looking to bvcp but I wanted to know if there is something else to look at. And I have nothing against russian people guys, my best friend is russian (but not living there).
  10. M

    bhyve Bhyve graphical control panel

    cbsd seems to be a cli/curses tool but ClonOS has some graphical interface. But ... all of this seems to be "made in russia" for the most part of it and nowdays it's not really a good point.
  11. M

    bhyve Bhyve graphical control panel

    Hi, I use FreeBSD since many years now but I'm new to bhyve. I search a graphical interface like you can have with vsphere or virtualbox. I know there are some of these like bvcp but I dont know witch are the interesting ones. Before else I'm a vsphere admin so the closer to vsphere hmtl...
  12. M

    Wifi AC - 2021

    Hi there, The main reason I don't use FreeBSD on my laptop@work is lack of recent wifi drivers. Last time I tried to install it I was forced to use an old wifi N stick as the internal wifi chipset was not recognised and wifi AC stick had no drivers too. So I ended with Linux as we ended with...
  13. M

    ZFS Get rid of zpool error

    I dont understand why you think I still have the corruption -in my data-. At first the corruption occured and a file was corrupted. In fact a DB file. So zpool status -v was showing the corrupted file name. So I dumped and restored the DB and the file was deleted so now zpool status -v shows ...
  14. M

    ZFS Get rid of zpool error

    So, zfs send and receive wont get rid of the error ... Maybe I should rsync to new pool and then make it bootable ?
  15. M

    ZFS Get rid of zpool error

    Hi there, I have an error on a zpool. That was related to a postgresql database file. I have no clue how this happened. So, I dumped the base and restored it. All good so far. Since this is a single device I understood that I cant correct the error with scrub even if it's no more related to any...
  16. M

    PF Rules on domains

    Well, that dont means anybody from anywhere can request the DNS like this. I'll check it soon.
  17. M

    PF Rules on domains

    HEY, that's it ! host -l -a somedomain.org dns.somedomain.org | awk '$4=="A" {print $5}' give me the list of all IPV4 addresses of that domain, 24379 addresses, wich I can enter in the rules. Of course the DNS server must allow this and this is not always the case. host -l -a google.com...
  18. M

    PF Rules on domains

    Once again, since not very visible without reading all the posts : pfblockerng can filter inbound on countries, right ? So anything.domain.cn can be blocked from accessing my lan. Maybe a domain could be configured aswell ? pfblockerng gurus there ?
  19. M

    PF Rules on domains

    I cant know the address in advance or it would be trivial to enter rules based on network and/or ip lists. One problem is that filtering tools are there to filter on destination domains and not on source domains. They can easily filter in on IP or Subnet but not on names. But, wait, pfblockerng...
  20. M

    PF Rules on domains

    Well that assume all network address of 111.111 are the same domain. Wich may be wrong. 111.111.1.12 should be srv1.somenet.org and 111.111.1.13 srv2.myothernet.org. Assuming I have more than one domain.
Back
Top