Search results

Well, I am talking about pkg version -l "<" which looks like a "subset" of pkg version -i, but in this case it seems I missed this "quarterly" introduction with 10.2. There will be a new quarter soon, so let's see :) Thanks.

pkg version -l shows that they are out of date. I also compared the current installed version with pkg info and freshports.org I can see there are a few candidates. EDIT: For example: ca_root_nss-3.71 < Current version should be 3.76, pkg version -l "<" tells me that it's out of date, but...

Hi, I am running FreeBSD 13.0-RELEASE-p7, which I upgraded from FreeBSD 12. I had some issues during the upgrade with pkg and had to run pkg bootstrap to make it work again. Now when I run pkg update && pkg upgrade the local repository is being updated but it always returns: Updating FreeBSD...

For later reference: No solution found, assuming a damaged NIC OR an incompatibility between AMD processor and this Intel chipset.

Yes, I will replace the network card with maybe a Broadcom. This seems to work and is similar priced. Thanks for your help and suggestions everybody!

I have only one module. Up to now (still running) no error. I would assume power is not an issue. I ran the same test with the onBoard NIC (also connected via PCIe lanes) without issues. At least for me it's very difficult to test. I read other have issues with those Intel NICs with the AMD...

Alright, I finally put Ubuntu Live Desktop (20.04 LTS) on a USB stick. When I ran apt update && apt install via the Intel card, it also rebooted. What it tells us? Most likely a hardware issue. I cant test the Intel card, so I need to either a) buy a new NIC b) buy new RAM I cant upgrade the...

I have a Debian live USB stick flying around. I will try that one.

Device 1K-blocks Used Avail Capacity /dev/ada0p3 8388608 0 8388608 0% I found something about issues with SMBus but the "hack" to cover 2 pins with tape seem not have worked up to now.

I set dumpdev="AUTO" in rc.conf, but no dump in /var/crash. I set: dev.igb.0.iflib.disable_msix=1 dev.igb.0.eee_control=0 hw.pci.do_power_suspend=0 But no use. As soon as I run iperf it will start with max. link speed (100 MBps) and go down to 0. After 2-3 seconds with 0 MBps it reboots. BIOS...

Is there a way to find out? It's a OPNsense instance but I am about to test it with Debian soon. memtest+ is on the list next. The system (Fujitsu S930) looks clean (was refurbished), but I will check the RAM anyway.

Seems Im not alone: https://www.reddit.com/r/PFSENSE/comments/da6nh7/multiport_intel_82571ebbased_network_cards_not/

I ran fsck to fix it, it said it fixed something but the panic remains. I will reinstall and try again. Thanks for your input so far. I was hoping there was an easy solution like the old "disable ACPI" days ;-) I will come back with news.

I need to find a way to get it to boot again. Currently it panics at boot after the last load test. Maybe I need to re-install and try again. Afterwards I try to get details from there. EDIT: It doesnt get to the boot loader and stops with db> but wont accept any input.

iperf output is like this before it dies: [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 11.3 MBytes 95.1 Mbits/sec [ 5] 1.00-2.00 sec 11.2 MBytes 94.2 Mbits/sec [ 5] 2.00-3.00 sec 11.2 MBytes 94.1 Mbits/sec...

I will try that. I didn't yet. Sadly this is my only machine I have with a PCIe slot. I can try to install a different OS and try again. The onboard card (RealTek) works without issues so far.

Hi, I bought a Intel Pro/1000 VT Quad-Port with a 82576 chip connected via PCIe x4 running FreeBSD 13. Once I put some load on the card, the system reboots without any hint on the screen or the logs. I did some research and found a hint regarding ASPM being enabled, but I didnt find a way to...

Hi, I wanted to run auditd on FreeBSD to monitor the jails. Now I found out that it wouldn't work as jails are not supported and running it inside a jail does not work either. Is there a recommendation for a simple system which alerts me when certain users login/fail to login, create files...

Thanks so much for your help! I did indeed update the whole system but thought that the current OpenSSL version had been in place before. I set --ssl-cipher=AES256-SHA:DHE-DSS-AES256-SHA:DHE-RSA-AES256-SHA in my my.cnf and it worked again. Thanks so much!!

Hi, I recently upgraded my MariaDB 5.5.41 server to 5.5.43. Since then I can not connect via SSL anymore. Besides the upgrade nothing has changed. When I try to connect via the MySQL client (MariaDB Client actually) I get the following error: ERROR 2026 (HY000): SSL connection error...