Search results

How did you make ppp.linkdown script run? I never get it to run. I copied from /usr/share/examples/ppp/ppp.linkdown.sample to /etc/ppp/ppp.linkdown and I changed in ppp.conf to enable lqr and echo. I did not see any action when I unplug the cable modem.

# # Macros # INT_IF = "em0" EXT_IF = "bge0" EXT_IF2 = "bge1" table <private_nets> persist { 127/8, 172.16/12, 192.168/16, 169.254/16 } # # Options and default policy # set block-policy drop set state-policy if-bound # # Packet normalization # scrub in all scrub out on...

Not working in FreeBSD.

Looks it needs a reboot to reconfigure the FreeBSD server make it change. I can keep checking the Internet connection, when it has no connection, I can change the configuration files such as /etc/rc.conf and issue a command "reboot". This is ugly, but I did not find a good solution. CARP needs...

LiveFS is different than FreeBSD installed on USB. For example, if you want to install ntfs, you can do the following if it is a FreeBSD on USB: cd /usr/ports/sysutils/fusefs-ntfs make -DBATCH install clean. If it is a livefs, you cannot do this. Can you?

I made freebsd FreeBSD 8.3 on 2GB USB. Everything is fine except there is a trick at /boot/loader.conf. You have to add: kern.cam.boot_delay=10000 Another step, I do not know it is a trick or not. You have to wipe out the whole disk before you fdisk it. dd if=/dev/zero of=/dev/da0 bs=512k No...

I made a lot of them with FreeBSD 9stable both 32 bit and 64bit by using sysinstall. Also I made a lot of USB sticks with FreeBSD 8.3prerelease amd64 and i386 by "make installworld DESTDIR=/mnt....." I will try to make some of 7.4.

I have built several FreeBSD servers by using non-ECC memory. It has no problem so far. I used 3TB hard drives and gmirrored them.

Thank you. I stay in 9.0RC2. No problem so far.

Hi, FreeBSD Pros! I just want to install php5.3.8 for drupal7. I have a hard time on 8.2 because it stopped at x11/libSM for php5-gd. So I switched to 9.0 RC2. I did a cvsup and make buildworld && make buildkernel KERNCONF=.. && make installkernel KERNCONF=... mergemaster ... uname -a ends up...

I was running FreeBSD access point for a couple of months. I am using TP-LINK TL-WN321G USB stick as the AP. The connection drops off every 5 to 10 minutes. I have to repair in Windows to fix it. Now I am recompiling the kernel to see if it is fixed or not.

How to set up hostapd when the wireless card used as a component of a bridge?

I got this problem but after I compile the lang/php5-curl, it is ok. But I cannot make php 5.3.3 work with lighttpd.

Hi, guys! I just made TP-LINK TL-WN321G USB wireless key worked with FreeBSD 8.2 with hostapd by using rum. In loader.conf, I put if_rum_load="YES" In hostapd.conf change hw_mode=a to hw_mode=g Now it is working! I can use Windows and Ubuntu to access it!

Hi, guys! I have installed FreeBSD on 8 Acer Aspire One computers. Only one got problem. After I installed, everything shows ok. Then I boot it. It reports Error 17. I used dump and restore from another hard drive. The same thing. Then I booted from another USB hard drive and did a bsdlabel -B...

I read on the internet says rum and 2cpu FreeBSD crashes. I give up rum and tried malo. But malo works only as a client no access point.

What is your Ralink card? I am looking for such a card for several days and I cannot find it.

Have you fixed the problem? I have the same problem. I used ath with no problem. I keep every thing the same, just replace ath0 with rum0. The client can connect the ap, but very soon, the ap crashed. Entropy harvesting: interrupts ethernet point_to_point kickstart This may be another problem...

Now finished 25.33%, 104.8 hours are still needed!

Hi, I am using a lap top computer with 512M memory a 8 G SSD hard drive. I am dumping and restoring a 6G partition from a 320G external USB 2 hard drive to the internal SSD hard drive partition. It has taken 2 days to finish 21% and it says finished in 120 hours later. So it takes 7 days to...