Solved Can't connect to my wifi home network...

ZioMario

ZioMario

Hello.

First of all I would like to know if you use a compact wi-fi adapter,if yes,which model it is. Please post a picture or I will be not able to understand which model works and I can buy.

I'm trying to connect to my wi-fi network using this adapter :

Code: 
ugen1.19: <Realtek e> at usbus1
rtwn0 on uhub1
rtwn0: <Realtek e, class 0/0, rev 2.10/2.00, addr 50> on usbus1
rtwn0: MAC/BB RTL8192EU, RF 6052 2T2R
wlan0: Ethernet address: 78:de:e0:0b:71:06

nano /etc/rc.conf :

Code: 
wlans_rtwn0="wlan0"
ifconfig_wlan0="WPA SYNCDHCP"
local_unbound_enable="YES"

nano /boot/loader.conf

Code: 
if_tap_load="YES"
if_bridge_load="YES"
bridgestp_load="YES"

if_rtwn_load="YES"
if_rtwn_usb_load="YES"
legal.realtek.license_ack=1

wlan_wep_load="YES"
wlan_ccmp_load="YES"
wlan_tkip_load="YES"

nano /etc/wpa_supplicant.conf :

Code: 
network={
        ssid="ziomario"
        priority=1
        #+ any_bssid
        key_mgmt=WPA-PSK
        proto=RSN
        psk="ciao"
}

on the router : WPA2

Code: 
marietto# ifconfig

em0: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP> metric 0 mtu 1500
    options=4e504bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,LRO,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
    ether
    inet 192.168.1.5 netmask 0xffffff00 broadcast 192.168.1.255
    media: Ethernet autoselect (1000baseT <full-duplex>)
    status: active
    nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>

lo0: flags=1008049<UP,LOOPBACK,RUNNING,MULTICAST,LOWER_UP> metric 0 mtu 16384
    options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
    inet 127.0.0.1 netmask 0xff000000
    inet6 ::1 prefixlen 128
    inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
    groups: lo
    nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

tap20: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP> metric 0 mtu 1500
    options=80000<LINKSTATE>
    ether
    groups: tap
    media: Ethernet 1000baseT <full-duplex>
    status: active
    nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
    Opened by PID 2451

wlan0: flags=8803<UP,BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
    options=0
    ether
    groups: wlan
    ssid "" channel 1 (2412 MHz 11g ht/20)
    regdomain FCC country US authmode WPA1+WPA2/802.11i privacy MIXED
    deftxkey UNDEF txpower 30 bmiss 7 scanvalid 60 protmode CTS ht20
    ampdulimit 8k ampdudensity 16 shortgi -stbc -ldpc -uapsd wme
    roaming MANUAL
    parent interface: rtwn0
    media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
    status: no carrier
    nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>

Code: 
marietto# wpa_supplicant -dd -i wlan0 -c /etc/wpa_supplicant.conf &

marietto# wpa_supplicant v2.11
Successfully initialized wpa_supplicant
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=8):
     7a 69 5f 6d 61 72 69 6f                           ziomario 
priority=1 (0x1)
key_mgmt: 0x2
proto: 0x2
PSK (ASCII passphrase) - hexdump_ascii(len=9): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 1
   id=0 ssid='ziomario'
wpa_driver_bsd_capa: drivercaps=0x0591c541,cryptocaps=0x0000000b
bsd_ctrl_iface: if wlan0 (changed) enable 0 IFF_UP 0
Add interface wlan0 to a new radio N/A
PTKSA: Initializing
wlan0: Failed to attach pkt_type filter
wlan0: Own MAC address: 18:de:d0:0b:71:06
bsd_set_key: alg=0 addr=0x0 key_idx=0 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=0
bsd_set_key: alg=0 addr=0x0 key_idx=1 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=1
bsd_set_key: alg=0 addr=0x0 key_idx=2 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=2
bsd_set_key: alg=0 addr=0x0 key_idx=3 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=3
bsd_set_key: alg=0 addr=0x0 key_idx=4 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=4
ioctl[SIOCS80211, op=20, val=0, arg_len=7]: Invalid argument
bsd_set_key: alg=0 addr=0x0 key_idx=5 set_tx=0 seq_len=0 key_len=0
bsd_del_key: key_idx=5
ioctl[SIOCS80211, op=20, val=0, arg_len=7]: Invalid argument
wpa_driver_bsd_set_countermeasures: enabled=0
wlan0: RSN: flushing PMKID list in the driver
wlan0: Setting scan request: 0.100000 sec
TDLS: TDLS operation not supported by driver
TDLS: Driver uses internal link setup
TDLS: Driver does not support TDLS channel switching
wlan0: WPS: UUID based on MAC address: e047946a-801d-5905-98b4-g41497accb62
ENGINE: Loading builtin engines
ENGINE: Loading builtin engines
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
MBO: Update non-preferred channels, non_pref_chan=N/A
wlan0: Added interface wlan0
wlan0: State: DISCONNECTED -> DISCONNECTED
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Starting AP scan for wildcard SSID
wlan0: Add radio work 'scan'@0x524c20010560
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'scan'@0x524c20010560 after 0.000014 second wait
wpa_driver_bsd_set_wpa: enabled=1
wpa_driver_bsd_set_wpa_internal: wpa=3 privacy=1
bsd_ctrl_iface: if wlan0 (changed) enable 1 IFF_UP 1
ioctl[SIOCS80211, op=103, val=0, arg_len=128]: Network is down
wlan0: State: SCANNING -> DISCONNECTED
wlan0: CTRL-EVENT-SCAN-FAILED ret=-1 retry=1
wlan0: Radio work 'scan'@0x524c20010560 done in 37.865932 seconds
wlan0: radio_work_free('scan'@0x524c20010560): num_active_works --> 0
wlan0: Setting scan request: 1.000000 sec
EAPOL: disable timer tick
RTM_IFINFO: Interface 'wlan0' UP
wlan0: Event INTERFACE_ENABLED (25) received
wlan0: Interface was enabled
RTM_IFINFO: Interface 'wlan0' DOWN
wlan0: Event INTERFACE_DISABLED (26) received
wlan0: Interface was disabled
wlan0: State: DISCONNECTED -> DISCONNECTED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wlan0: State: DISCONNECTED -> INTERFACE_DISABLED
wlan0: Event SCAN_RESULTS (3) received
Error reading packet, has device disappeared?
Error reading packet, has device disappeared?

wlan0: Removing interface wlan0
wlan0: Request to deauthenticate - bssid=00:00:00:00:00:00 pending_bssid=00:00:00:00:00:00 reason=3 (DEAUTH_LEAVING) state=INTERFACE_DISABLED valid_links=0x0 ap_mld_addr=00:00:00:00:00:00
TDLS: Tear down peers
QM: Clear all active DSCP policies
wlan0: CTRL-EVENT-DSCP-POLICY clear_all
wpa_driver_bsd_set_countermeasures: enabled=0
ioctl[SIOCS80211, op=25, val=0, arg_len=0]: Device not configured
PTKSA: Deinit. n_ptksa=0
wlan0: WPA: Clear old PMK and PTK
wlan0: Cancelling scan request
wlan0: Cancelling authentication timeout
HS20: Delete all stored icons
QM: Clear all active DSCP policies
wlan0: CTRL-EVENT-DSCP-POLICY clear_all
Remove interface wlan0 from radio
Remove radio
wpa_driver_bsd_set_wpa: enabled=0
wpa_driver_bsd_set_wpa_internal: wpa=0 privacy=0
bsd_set_opt_ie: set WPA+RSN ie (len 0)
ioctl[SIOCS80211, op=95, val=208, arg_len=0]: Device not configured
ioctl[SIOCS80211, op=17, val=0, arg_len=0]: Device not configured
ioctl[SIOCS80211, op=26, val=0, arg_len=0]: Device not configured
ioctl[SIOCGIFFLAGS]: Device not configured
wpa_driver_bsd_set_wpa_internal: wpa=2 privacy=1
ioctl[SIOCS80211, op=17, val=1, arg_len=0]: Device not configured
ioctl[SIOCS80211, op=26, val=2, arg_len=0]: Device not configured
ioctl[SIOCS80211, op=16, val=2, arg_len=0]: Device not configured
wpa_driver_bsd_deinit: failed to restore roaming state
wlan0: CTRL-EVENT-TERMINATING

it is not able to assign an IP to wlan0.

On dmesg :

Code: 
ugen1.19: <Realtek e> at usbus1 (disconnected)
rtwn0: at uhub1, port 9, addr 50 (disconnected)
rtwn0: r92e_power_off: failed to block Tx queues
rtwn0: detached
usb_alloc_device: set address 19 failed (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 19 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=19, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 19 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=19, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 19 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=19, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 19 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=19, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 19 failed, USB_ERR_IOERROR
ugen1.19: <Unknown > at usbus1 (disconnected)
uhub_reattach_port: could not allocate new device
 
We can say that the problem is fixed. That adapter is not good for FreeBSD. I chosen another one and boom. Worked like a charme. Finding one that works seems like hitting the jackpot.

Code: 
rum0 on uhub1
rum0: <WLAN 802.11g USB WLAN Card, class 6/2, rev 2.00/0.01, addr 62> on usbus1
rum0: MAC/BBP RT2573 (rev 0x2573a), RF RT2528
wlan1: Ethernet address: 00:0e:8e:11:8c:4b
wlan1: link state changed to UP

wlan1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
    options=0
    ether 00:0e:4e:19:8c:4b
    inet 192.168.1.7 netmask 0xffffff00 broadcast 192.168.1.255
    groups: wlan
    ssid ziomario channel 1 (2412 MHz 11g) bssid b2:a5:ef:34:6f:eb
    regdomain FCC country US authmode WPA2/802.11i privacy ON
    deftxkey UNDEF AES-CCM 2:128-bit txpower 30 bmiss 7 scanvalid 60
    bgscan bgscanintvl 300 bgscanidle 250 roam:rssi 7 roam:rate 5
    protmode CTS wme roaming MANUAL
    parent interface: rum0
    media: IEEE 802.11 Wireless Ethernet OFDM/48Mbps mode 11g
    status: associated
    nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
 
I use these two models.

Edimax EW-7811UN V2

And Atheros QCNFA222 AR5BWB222
 

Attachments

  • atheros.jpg
    atheros.jpg
    117.2 KB · Views: 158
  • edimax.jpg
    edimax.jpg
    25.1 KB · Views: 163
ZioMario said:
Atheros is not good for a phone
Click to expand...
I chose an Atheros atk9 card years ago for LibreBoot (it was one of the most open-source wifi cards available iirc). I think newer atk10 stuff has a different rep though. It looks like QCNFA222 is atk9.

If atk9 has the same good support on FreeBSD like Linux, I'd go for that!
 
Espionage724 said:
I chose an Atheros atk9 card years ago for LibreBoot (it was one of the most open-source wifi cards available iirc). I think newer atk10 stuff has a different rep though. It looks like QCNFA222 is atk9.

If atk9 has the same good support on FreeBSD like Linux, I'd go for that!
Click to expand...

Did u understand that I'm building a phone ? the adapter should be small,like the Edimax one. I can't make a phone that looks like a brick.
 
My Ralink RT2501/ RT2573 Wireless USB Stick does not work under FreeBSD 14.2 installed on the Radxa Zero 3W (it does not create the wlan0 network interface).

The manpage of "ral" mentions that it supports "PCI/PCIe/CardBus wireless adapters based on the Ralink RT2500, RT2501, RT2600, RT2700, RT2800, RT3090 and RT3900E chipsets".

Ok the chipset of my wifi stick is RT2501/ RT2573,but it is USB,not PCI/PCIe/CardBus,so I suppose that's the wrong driver.

Instead,I tried the "run" driver. It didn't work,because it supports "USB 2.0 wireless adapters based on the Ralink RT2700U, RT2800U, RT3000U and RT3900E chipsets) ; not my chipset.

What's the proper driver to use ? Take in consideration that it worked on my x86_X64 Intel PC,why it shouldn't on the Radxa ?

Unfortunately I can't know which driver it uses,because on my PC it is embedded inside the kernel,instead on the Radxa I should load the driver from the proper ko file.
 
LibreQuest said:
I use these two models.

Edimax EW-7811UN V2

And Atheros QCNFA222 AR5BWB222
Click to expand...

Hello bro.

I've just got the Edimax EW-7811UN V2 dongle to my home. Can you tell me what's the name of the kernel module to load to be able to enable it ? thanks.
 
You must log in or register to reply here.
Back
Top