D
Deleted member 2077
Guest
Hello. I am having troubles configuring both my video card and monitor and hoping for some assistance.
Video Card
I'm using an Intel DN2800MT motherboard which has a Intel NM10 Express Chipset. Best I can tell, the graphics card is an Intel GMA 3650:
Graphics
•Intel Graphics Media Accelerator 3650
Manual
Technical Specs
dmesg
`Xorg -configure` detect it as this:
I tried the /usr/ports/x11-drivers/xf86-video-intel drive and gives this:
/var/log/Xorg.0.log
I'm assuming it is not supported at this time?
Monitor
Acer x163W
Native resolution: 1366x768 @ 60Hz
With the "vesa" driver, the X server comes up; but in a really weird resolution. Something like 1493x768. I'd be ok with using this driver is I can get the monitor resolution sorted out.
How do I set it up for 1366x768? I tried this:
But like I said, comes up in some odd resolution. The manual states that it should be run in the 1366x768 mode for "optimal quality".
Video Card
I'm using an Intel DN2800MT motherboard which has a Intel NM10 Express Chipset. Best I can tell, the graphics card is an Intel GMA 3650:
Graphics
•Intel Graphics Media Accelerator 3650
Manual
Technical Specs
dmesg
Code:
vgapci0: <VGA-compatible display> port 0x40d0-0x40d7 mem 0xd0600000-0xd06fffff irq 16 at device 2.0 on pci0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
`Xorg -configure` detect it as this:
BoardName "Atom Processor D2xxx/N2xxx Integrated Graphics Controller"
I tried the /usr/ports/x11-drivers/xf86-video-intel drive and gives this:
/var/log/Xorg.0.log
Code:
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.7.7, module version = 2.7.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, IGD_GM, IGD_G, 965G, G35,
965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
Mobile Intel<C2><AE> GM45 Express Chipset,
Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41
(II) Primary Device is: PCI 00@00:02:0
(EE) No devices detected.
Fatal server error:
no screens found
I'm assuming it is not supported at this time?
Monitor
Acer x163W
Native resolution: 1366x768 @ 60Hz
With the "vesa" driver, the X server comes up; but in a really weird resolution. Something like 1493x768. I'd be ok with using this driver is I can get the monitor resolution sorted out.
How do I set it up for 1366x768? I tried this:
Code:
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1366x768"
EndSubSection
EndSection
But like I said, comes up in some odd resolution. The manual states that it should be run in the 1366x768 mode for "optimal quality".