[Solved] How can I install a 3TB HDD?

ghostcorps · #1 September 5th, 2012, 16:51

Hi guys,

I am trying to install a 3TB Seagate HDD but it is not as easy as I expected... nothing ever is.

Using this thread I have tried the following method:

First I get the disk info:

Code:

ad12
        512             # sectorsize
        3000592982016   # mediasize in bytes (2.7T)
        5860533168      # mediasize in sectors
        5814021         # Cylinders according to firmware.
        16              # Heads according to firmware.
        63              # Sectors according to firmware.
        W1F03HGG        # Disk ident.

Using the thread above I calculate the following to be the correct geometry:

Code:

        32768            # sectorsize
        3000592982016    # mediasize in bytes (2.7T)
        5860491264       # mediasize in sectors
        5814021          # Cylinders according to firmware.
        16               # Heads according to firmware.
        63               # Sectors according to firmware.
        W1F03HGG         # Disk ident.

I set this geometry in fdisk though sysinstall:

Code:

Disk name:      ad12                                   FDISK Partition Editor
DISK Geometry:  5814021 cyls/16 heads/63 sectors = 5860533168 sectors (2861588MB)

Offset       Size(ST)        End     Name  PType       Desc  Subtype    Flags

         0         63         62        -     12     unused        0
        63 5860533105 5860533167   ad12s1      8    freebsd      165

I then use newfs to create the filesystem as follows:

Code:

# newfs -S 4096 -b 32768 -f 4096 -O 2 -U -m 8 -o space -L mediabackup /dev/ad12s1

But rather than using the geometry I set previously it uses the following:

Code:

/dev/ad12s1: 764436.4MB (1565565808 sectors) block size 32768, fragment size 4096
        using 1034 cylinder groups of 740.00MB, 23680 blks, 47360 inodes.
        with soft updates

This results in a partition of 735G.

Where did I go wrong?

**SirDice** · #2 September 5th, 2012, 16:58

Don't use sysinstall(8), it's deprecated.

The maximum disk size supported by MBR is about 2TB, I suggest you use gpart(8) and the GPT scheme.

**wblock@** · #3 September 5th, 2012, 17:05

That thread is old and somewhat outdated. Disk Setup On FreeBSD shows how to use gpart(8) to set up aligned GPT partitions.

Fixed drive geometry is an obsolete concept. Drives put more sectors on the outer tracks because there is more room, and have been doing that for many years. So trying to calculate an imaginary geometry to satisfy the imaginary geometry used by fdisk(8) is pointless. GPT is easier and more versatile.

ghostcorps · #4 September 5th, 2012, 18:15

Thanks for the quick reply guys!

I'll give that article a go.

ghostcorps · #5 September 5th, 2012, 18:54

Aaaaand it's done, too easy

Thanks again guys.

On a sidenote, if anyone is here with the same question you will likely need to destroy the partition before beginning, as explained HERE

**wblock@** · #6 September 5th, 2012, 19:27

Quote:

Originally Posted by ghostcorps

On a sidenote, if anyone is here with the same question you will likely need to destroy the partition before beginning, as explained HERE

A easier way, without having to delete all the partitions first:
# gpart destroy -F ada0

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
trying to convert scripted install iso to pxe install but fails trying to mount acd0	highurtenflurst	Installing & Upgrading	6	March 2nd, 2012 23:57
HOWTO: Install FreeBSD8.2 on Laptop when Firewire and ACPI blocks normal install disc	Identical	Howtos & FAQs (Moderated)	0	November 27th, 2011 10:46
Going for first install with some doubts (Processor Family, Medium, Chroot Install)	vfbsilva	Installing & Upgrading	18	July 18th, 2011 14:52
Multi-boot install: partition sizes and install order	vodoomoth	Installing & Upgrading	3	December 25th, 2010 20:05
Do I need install Samba3 if samba4-devel install by default	mfaridi	Installation and Maintenance of FreeBSD Ports or Packages	1	September 16th, 2010 13:07

The Following User Says Thank You to wblock@ For This Useful Post:
ghostcorps (September 17th, 2012)