Search results

It was once, not everytime, I would say 1 in 1000 times. -- gnumonk

Any update on this? -- gnumonk

Here is log says 2013-04-18 19:16:09.678164 rule 2..16777216/0(match): pass in on rl0: 192.168.1.7.57192 > 192.168.1.5.22: Flags [S], seq 2806091858, win 12800, options [mss 1280,sackOK,TS[|tcp]>

@tingo, Single user mode was not an option, much before it gets halted :) -- gnumonk

Ah, It looks like an issue with FreeBSD with hardware. I have done following steps. I have three disk in box two SATA and one IDE. I have unplugged all SATA except one when I will reinstall BSD FreeBSD, but I found the same behaviour. Then I unplugged the CDROM (which is also SATA), here I...

This issue has started after power went off, suspecting that something wrong with the disk? Is there anyway I can run fsck from FreeBSD bootloader? -- gnumonk

Ah, pf stuck again and I am at a remote location, need to go to my work location to reboot the server or disable the pf. It's not ok. :( -- gnumonk

Ah no this is not working, tried with rebooting the system too. No luck. tcpdump -vv -n -e -ttt -i pflog0 tcpdump: WARNING: pflog0: no IPv4 address assigned tcpdump: listening on pflog0, link-type PFLOG (OpenBSD pflog file), capture size 65535 bytes ^C 0 packets captured 0 packets received by...

Thanks for sharing this info, I have seen some of them which I used daily using git, but I see those are poiting to old link or dead link. I will probably take those. But I have a question, since most of the projects were moved to git, how to versioning them, I mean what will be on PORTVERSION...

Kpa, I have applied the rule. This is what pfctl -s info says: No ALTQ support in kernel ALTQ related functions disabled Status: Enabled for 0 days 00:52:29 Debug: Urgent State Table Total Rate current entries 0...

Thanks, @kpa. Let me apply those and let you know. -- gnumonk

If you are in X, just type in console: xset b off For me sysctl works too. -- gnumonk

Team, I have a FBSD FreeBSD box (9.1-RELEASE) behind a corporate firewall. I wanted to use PF to restrict access tor my box. I have the following rules in pf.conf: # cat pf.conf #Macros my_int = "rl0" tcp_services = "{ ssh, http, domain, ntp }" udp_services = "{ domain, ntp}" # Let's just...

Yes, I am also suspecting the same. I would like to make sure that issue is not something else? Is there any way I can boot the machine disabling some parameter? @ta0kira, I will check the BIOS setting and set the value to 1330? Let's see if I am able to boot. -- gnumonk

Kavin, How to get this information and how to set this? -- gnumonk

@jem, Will check CPU temperature readout from BIOS and update here. I had removed the CPU and processor fan and re-applied back. @Ondra, I need to look for this, But don't see any temp issue here, because system has been up for the last two days with Debian.

Beeblebrox, Yes, I tried with enable/disable single mode, enable/disabled ACPI, enabled/disable verbose, No luck so far. -- gnumonk

Console is not an option. I am not able to boot to the prompt, it gets halted earlier. I don't think it's overheating because it booted the first time and if I reboot with Debian it works fine. Anyway to debug? -- gnumonk

Hi, I had installed FreeBSD 9.x as desktop on AMD phenom2, after installation it was automatically rebooted in a day or two, I was suspecting that it might be due to dust bunnies. After cleaning CPU and fan, FreeBSD shows me boot prompt and when I boot it gets halted in 3-5 seconds. Please...

I have tried cd /usr/ports/editor/libreoffice/ and then make config and make install, it was running for two days? I then canceled this and installed with pkg_add -r -v libreoffice. I was able to installed but there were shared library issue came because my machine was mostly build with make and...